Mazda MX-6 1998 Скачать руководство пользователя страница 1090 | Manualshive

Страница: 1090 / 1282

background image

TROUBLESHOOTING [AUDIO]

3

Poor sound quality only when radio is played

TROUBLESHOOTING HINTS

Malfunction in audio unit input signal circuit

© Poor sound quality

•   Malfunction  in  reception
•   Audio unit malfunction
•   Manual antenna malfunction

• Power antenna malfunction

•   Front antenna feeder malfunction
•   Rear antenna feeder malfunction
•   Poor installation of manual antenna mast
•   Poor installation  of spacer

STEP

INSPECTION

ACTION

1

When radio wave was received at another
position, is sound quality normal?

Yes

Troubleshooting completed. (Cause of malfunction is

reception outside service area of radio station.)

No

Go to next step.

2

Is manual antenna equipped?

Yes

Go to next step.

No

Go to step 4.

3

Is manual antenna mast properly installed?

Yes

Go to next step.

No

Reinstall manual antenna mast.

4

Is spacer properly installed?

W 6 U 9 0 1 W S B

Yes

Go to next step.

No

Reinstall spacer.

tr

0 9-20 MANUAL ANTENNA

REMOVAL/INSTALLATION

tr

09-20 POWER ANTENNA

REMOVAL/INSTALLATION

5

Equipped with manual antenna:
Inspect manual antenna.

tr

0 9 -2 0 MANUAL ANTENNA

INSPECTION

Is manual antenna normal?
Equipped with power antenna:
Inspect power antenna.

c r 0 9 -2 0 POWER ANTENNA

INSPECTION

Is power antenna normal?

Yes

Go to next step.

No

Equipped with manual antenna:
Replace manual antenna.

tr

0 9 -2 0 MANUAL ANTENNA

REMOVAL/INSTALLATION

Equipped with power antenna:
Replace power antenna.

tr

0 9-20 POWER ANTENNA

REMOVAL/INSTALLATION

6

Inspect front antenna feeder.

tr

0 9 -2 0 FRONT ANTENNA FEEDER

INSPECTION

Is front antenna feeder normal?

Yes

Go to next step.

No

Replace front antenna feeder.

tr

09-20 FRONT ANTENNA FEEDER

REMOVAL/INSTALLATION

7

Inspect rear antenna feeder.

tr

0 9 -2 0 REAR ANTENNA FEEDER

INSPECTION

Is rear antenna feeder normal?

Yes

Replace audio unit.

tr

0 9-20 AUDIO UNIT INSTALLATION

No

Replace rear antenna feeder.

tr

09-20 REAR ANTENNA FEEDER

REMOVAL/INSTALLATION

4

Poor sound quality only when CD is played

TROUBLESHOOTING HINTS

Malfunction in output signal system of software

© Poor sound quality

• CD malfunction

Malfunction in audio unit operation signal circuit

© Poor sound quality

• Audio unit malfunction

0 9 -0 1 N -7

«
...
1088
1089
1090
1091
1092
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: Aries Страницы: 3

Бренд: Mercedes-Benz Страницы: 30

Бренд: Ford Страницы: 38

Бренд: Mercedes-Benz Страницы: 373

Road Ready Seat Protector

Бренд: Wagan Страницы: 12

Бренд: Chevrolet Страницы: 50

Бренд: Harman Kardon Страницы: 16

Бренд: TATA Motors Страницы: 184

PW-50C Civilian

Бренд: B&G electronics Страницы: 7

Бренд: Ford Страницы: 8

Бренд: Intec Страницы: 16

Challenger 2013

Бренд: Dodge Страницы: 543

Бренд: Unex Страницы: 30

Бренд: Atera Страницы: 3

Бренд: Black Horse Страницы: 5

Бренд: Demco Страницы: 4

Бренд: Gator Страницы: 6

Бренд: F.lli Menabo Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды