Mazda MX-6 1998 Скачать руководство пользователя страница 106

Страница: 106 / 1282

TROUBLESHOOTING [ENGINE CONTROL FS]

STEP

INSPECTION

ACTION

INSPECTION OF VACUUM HOSES
• Key off.

• Pull slightly on vacuum hoses at pressure

control valve, FTP sensor, fuel filler pipe
and fuel tank.

• Check for loose connections.
• Visually inspect for improper connections

and cracked hoses between fuel tank and

FTP sensor, fuel tank and pressure control

valve, fuel filler pipe and pressure control
valve and pressure control valve and
charcoal canister.

• Confirm the air tightness of vacuum hose

using vacuum pump.

•

is fault detected?

Yes

SERVICE or REPLACE as necessary.
RECONNECT all components.
RESET PCM to completely clear DTCs.

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

RECONNECT all components.
Go to next step.

CHECK FOR PRESSURE CONTROL VALVE
• Remove and inspect pressure control

valve.

•

Is fault detected?

Yes

REPLACE  pressure control valve.
RECONNECT all  components.
RESET  PCM to completely clear DTCs.

After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

RECONNECT all components.
Go to next step.

INSPECTION FUEL FILLER PIPE

• Remove fuel filler pipe.
• Visually inspect for fuel filler pipe damage.
•

Is fault detected?

Yes

REPLACE fuel filler pipe.
RECONNECT all components.
RESET PCM to completely clear DTCs.

err

After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

RECONNECT all components.
Go to next step.

INSPECTION OF FUEL TANK

•   Remove fuel tank.
•   Visually inspect for fuel tank damage.
•   Visually inspect for insufficient sealing or

poorly attached accessories on fuel tank:
i.e., fuel gauge.

•

Is fault detected?

Yes

SERVICE or REPLACE fuel tank or sealing.
RECONNECT all components.
RESET PCM to completely clear DTCs.

After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

RECONNECT all components.
Go to next step.

CHECK CANISTER  DRAIN  CUT VALVE
(CDCV)
•   Key off.
•   Remove CDCV.
•   Confirm CDCV is not damaged,  and that air

vents are tight when at ON.

•

Is fault detected?

Yes

REPLACE CDCV.
RECONNECT all components.
RESET PCM to completely clear DTCs.

t r

After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

Inspect and repair any detached, incorrectly installed or

cracked hoses between the charcoal canister and CDCV.

RECONNECT all components.
RESET PCM to completely clear DTCs.

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

0 1 -0 1 A -7 8

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды

Mazda MX-6 1998, Руководство по ремонту

Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды