Mazda MX-6 1998 Скачать руководство пользователя страница 992

Страница: 992 / 1282

TROUBLESHOOTING [REAR WINDOW DEFROSTER]

STEP

INSPECTION

ACTION

Press rear window defroster switch on.
Measure voltage at terminal A at filament

connector of wiring harness.

Is voltage

B+?

Yes

Go to next step.

Repair wiring harness between rear window defroster
relay and filament.

Disconnect filament connector.
Remove the C-piller trim.
Is filament installed to body ground securely?

Yes

Repair filament.

Repair wiring harness between filament and ground.

Rear window defroster does not continuously operate for 15 minutes, followed by cycle of three minutes off

and two minutes on

TROUBLESHOOTING HINTS

Malfunction in rear window defroster operation circuit

0 Rear window defroster does not continuously operate for

minutes, followed by cycle of three minutes off and two min

utes on
• CPU malfunction

STEP

INSPECTION

ACTION

—

Replace CPU.

0 9 -0 1 B -5

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-6 1998

Отзывы:

Mazda MX-6 1998, Руководство по ремонту, Страница: 992 / 1282

Результаты поиска

Содержание MX-6 1998

Отзывы: