Mazda MX-6 1998, Руководство по ремонту

Страница: 786 / 1282

CLUTCH
05-10 CLUTCH
GENERAL PROCEDURES (CLUTCH) .0 5 - 1 0 - 1
Clutch Pipe R em oval/Installation 05-10-1
CLUTCH FLUID INSPEC TIO N ..................05-10-1
CLUTCH FLUID REPLACEM ENT
05-10-1
CLUTCH PEDAL ADJUSTMENT ............ 0 5 -1 0 -2
Clutch Pedal H e ig h t................................ 0 5 -1 0 -2
Clutch Pedal Free Play .......................... 0 5 -1 0 -2
CLUTCH PEDAL
REM OVAL/INSTALLATION....................0 5 -1 0 -3
Clutch Pedal Installation Note .............. 0 5 -1 0 -3
CLUTCH MASTER CYLINDER
REMOVAL/INSTALLATION ....................0 5 -1 0 -4
CLUTCH MASTER CYLINDER
DISASSEM BLY/ASSEM BLY.................. 0 5 -1 0 -5
Snap Ring Disassembly/Assembly Note . 0 5 -1 0 -5
CLUTCH RELEASE CYLINDER
REMOVAL/INSTALLATION ....................0 5 -1 0 -6
CLUTCH RELEASE CYLINDER
DISASSEMBLY/ASSEMBLY................0 5 -1 0 -6
CLUTCH UNIT
REMOVAL/INSTALLATION..................0 5 -1 0 -7
Clutch Cover and Disc Removal Note . 0 5 -1 0 -8
Pilot Bearing Removal Note ................ 0 5 -1 0 -8
Flywheel Removal N o te ........................ 0 5 -1 0 -8
Flywheel Installation N o te .................... 0 5 -1 0 -8
Pilot Bearing Installation Note ............ 0 5 -1 0 -8
Clutch Disc Installation N o te ................ 0 5 -1 0 -8
Clutch Cover Installation Note ............ 0 5 -1 0 -9
CLUTCH COVER INSPECTION ............0 5 -1 0 -9
CLUTCH DISC IN S P E C TIO N .................... 0 5 -1 0 -1 0
CLUTCH RELEASE COLLAR
INSPEC TIO N ............................................. 0 5 -1 0 -1 0
PILOT BEARING INSPEC TIO N ................ 0 5 -1 0 -1 0
FLYWHEEL INSPECTION ........................0 5-10-11
GENERAL PROCEDURES (CLUTCH)
Clutch Pipe Removal/Installation
1. If any clutch pipe has been disconnected any time
during the procedure, add brake fluid, bleed the
air, and inspect for leakage after the procedure
has been completed.
2. If removing the clutch pipe, remove it by using the
SST (49 0259 770B). If installing the clutch pipe,
adjust the clutch pipe tightening torque to allow for
the use of a torque wrench-SST (49 0259 770B)
combination, and then tighten the clutch pipe by
using the SST (49 0259 770B).
CLUTCH FLUID INSPECTION
W 6 U 5 1 0 W 0 2
Note
• The fluid in the reservoir must be maintained
between the MIN/MAX level during
replacement.
CLUTCH FLUID REPLACEMENT
Caution
• Be careful not to spill clutch fluid on a
painted surface. If this should happen,
wash it off immediately.
• Do not mix different brands of clutch fluid.
• Do not reuse the clutch fluid that was
drained out.
1. Draw the fluid from the reservoir with a suction
pump.
2. Remove the bleeder cap from the clutch release
cylinder and attach a vinyl hose to the bleeder
plug.
3. Place the other end of the vinyl hose into a
container.
4. Slowly pump the clutch pedal several times.
5. With the clutch pedal depressed, loosen the
bleeder screw by using the SST to let fluid
escape. Close the bleeder screw by using the
SST.
W 6 U 5 1 0 W 0 3
6. Repeat steps 4 and 5 until only clean fluid is seen.
7. Tighten the bleeder screw.
Tightening torque
5.9— 8.8 N-m {60— 90 kgf-cm, 53— 78 ft-lbf}
8. Add fluid to the MAX mark.
9. Inspect for correct clutch operation.
0 5 -1 0 -1