Mazda MX-6 1998 Скачать руководство пользователя страница 293

Страница: 293 / 1282

TROUBLESHOOTING [ENGINE CONTROL KL]

DTC

P0703

Brake switch input malfunction

DESCRIPTION

• Continuous Memory DTC P0703 indicates brake switch input fault

[Possible Cause]

• Open to ground or power

• Damaged PCM

• Damaged brake switch

STEP

INSPECTION

ACTION

CHECK OPERATION OF BRAKE LIGHT

• Apply and release brake pedal several

times and observe brake light operation.

• Does brake light operate normally?

Yes

Go to next step.

Go to step 3 if brake light is never on.
Go to step 5 if brake light is always on.

CHECK FOR PCM BOO PID CYCLING

•   Key on,  engine off.
•   Access  BOO  PID.
•   Apply and  release brake pedal several

times while viewing BOO PID.

Note

• If BOO PID is not accessible, check brake

light circuit.

•

Does BOO PID cycle ON/OFF?

Yes

Go to Pinpoint Test for Intermittent key on engine off

(KOEO) input sensor wiggle procedure.

Check brake light circuit.

CHECK FOR POWER CIRCUIT TO BRAKE
SWITCH

Note

• Using 12 volt test lamp, verify integrity of

related fuses In fuse panel and check

condition of brake light bulbs before
starting this test.

• Key off.

• Disconnect brake switch.
• Measure brake light input voltage between

brake switch and chassis ground.

•

Is voltage greater than 10.5 volts?

Yes

Go to next step.

SERVICE open power circuit to brake switch.

RECONNECT switch.
RESET PCM to completely clear DTCs.

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

VERIFY  INTEGRITY OF  BRAKE  SWITCH
•   Brake switch  disconnected.
•   Connect digital  multimeter test probes to

brake switch terminals at brake switch.

• Apply brake pedal while monitoring

reading.

• Is resistance less than 5.0 ohms?

Yes

SERVICE open circuit between brake switch and

stoplamp ground.

RECONNECT brake switch.
RESET PCM to completely clear DTCs.

c r After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

REPLACE brake switch.
RECONNECT brake switch. RESET PCM to completely

clear DTCs.

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

VERIFY BRAKE SWITCHES NOT ALWAYS

CLOSED
•   Key off.
•   Brake switch disconnected.
•   Key on,  Engine off.
•

Is brake light still on?

Yes

Go to next step.

VERIFY proper installation of brake switch.

If okay, REPLACE brake switch.
RECONNECT brake switch.

RESET PCM

to completely clear

DTCs.

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

CHECK  FOR  SHORT TO  POWER  CIRCUIT
IN  PCM
•   Key off.
•   Brake switch disconnected.
•   Key on,  engine off.

• Is brake light still on?

Yes

Go to next step.

REPLACE PCM.
RECONNECT brake switch.
RERUN OBD Test.

0 1-01B-87

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-6 1998

Отзывы:

Mazda MX-6 1998, Руководство по ремонту, Страница: 293 / 1282

Результаты поиска

Содержание MX-6 1998

Отзывы: