Mazda MX-6 1998 Скачать руководство пользователя страница 238 | Manualshive

Страница: 238 / 1282

background image

TROUBLESHOOTING [ENGINE CONTROL KL]

STEP

INSPECTION

ACTION

6

CHECK  HEATED  OXYGEN  SENSOR
CIRCUIT  RESISTANCE
•   Key off.

• PCM connected to vehicle harness.

• Disconnect suspected heated oxygen

sensor connector.

•   NGS tester connected.
•   Key on,  engine off.
•   Access correct heated oxygen sensor PID.

• 02S 12

Note

• Heated oxygen sensor displayed as

0 2 S 1 2 (Middle) on NGS tester.

• Heated oxygen sensor (Middle)=Test

Pin 35 and 97

•

Is voltage greater than 1.5 volts?

Yes

Go to step 9.

No

Go to next step.

7

CHECK  RESISTANCE OF HEATED OXYGEN
SENSOR  GROUND  CIRCUIT  IN  PCM
•   Key off.
•   PCM connected to breakout box.  vehicle

harness disconnected from breakout box.

• Measure the resistance between Test Pin

35 (Middle), 60 (Front RH), 61 (Rear), 87

(Front LH) and Test Pin 91 at breakout box.

•

Is resistance reading less than 5.0

ohms?

Yes

REMOVE breakout box.
RECONNECT PCM.

Go to next step.

No

REPLACE PCM.
REMOVE breakout box.
RECONNECT all components.

o» After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

8

APPLY  12 VOLTS TO  SUSPECT  HEATED
OXYGEN  SENSOR  CIRCUIT
•   Key off.
•   Heated oxygen sensor (middle)

disconnected.

• Jumper power to heated oxygen sensor

signal circuit at vehicle harness connector.

• Key on.
• Access heated oxygen sensor PID and

Monitor.
• 02S 12 PID

• Is PID voltage greater than 1.5 volts?

Yes

REPLACE heated oxygen sensor.
RECONNECT all components.
RESET PCM to completely clear DTCs.

tr

After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

No

REPLACE PCM.
RECONNECT all components.
RESET PCM to completely clear DTCs.

w

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

9

CHECK  FOR OVER  VOLTAGE  ON  HEATED
OXYGEN  SENSOR  CIRCUIT  IN  PCM
•   Key on.
•   PCM  connected to vehicle  harness.
•   Heated oxygen sensor disconnected.
•   Inspect both ends of connect for damaged

or pushed out pins, moisture, corrosion,
loose pins, etc. and service as necessary.

• Measure voltage between PCM ground

Test Pin at heated oxygen sensor vehicle

harness connector and battery negative
post.

• Measure voltage between heated oxygen

sensor signal Test Pin at heated oxygen
sensor vehicle harness connector and
battery negative post.

•

Are voltage readings greater than 1.5

volts?

Yes

REPLACE  PCM.
RECONNECT all components.
COMPLETE  OBD  II  Drive  Mode.
RERUN  OBD Test.

No

REPLACE heated oxygen sensor.
RECONNECT all components.
RESET PCM to completely clear DTCs.

tr

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

0 1 -0 1 B -3 2

«
...
236
237
238
239
240
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: A-Tach Mounts Страницы: 2

Бренд: Hama Страницы: 2

Бренд: Toyota Страницы: 35

Бренд: EUFAB Страницы: 12

MILSCO KIT# C746700

Бренд: K&M Страницы: 2

Бренд: Car-Interface Страницы: 25

2 Bike Carrier 977

Бренд: Thule Страницы: 6

Бренд: Harbor Freight Tools Страницы: 12

Бренд: Honda Страницы: 3

Бренд: Jeep Страницы: 1528

Бренд: AddSecure Страницы: 14

Бренд: Whispbar Страницы: 15

Бренд: Saab Страницы: 92

Бренд: A-rival Страницы: 23

Бренд: ULTIMATE SPEED Страницы: 10

Бренд: HAKR Страницы: 9

Бренд: Mazda Страницы: 1001

Airgo Active cushion / Comfort

Бренд: TOGU Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды