manualshive.com logo in svg

Mazda MX-6 1998, Руководство по ремонту, Страница: 1218 / 1282

Поделиться
Скачать
Mazda MX-6 1998 Скачать руководство пользователя страница 1218

INTERIOR TRIM

REAR  DOOR TRIM  REMOVAL/INSTALLATION

W 6 U 9 1 7 W 2 0

1.  Disconnect the  negative  battery cable  if equipped 

9.  Install  In the  reverse order of  removal, 

with a power window.

2.  Remove the  regulator handle if equipped with  a 

manual window.

3.  Remove the screw to  remove the  inner handle.
4.  Turn  over the  recess cover to  remove the  screw.
5.  Remove the fasteners.
6.  Pull the  rear door trim to disengage clips A from 

the  body.

7.  Pull the  rear door trim  upward to disengage  hooks 

B from the  body.

8.  Disconnect the connector if equipped with a power 

window.

CLIP

HOOK

4U.

A

W 6 U 9 1 7 W A M

A-PILLAR TRIM  REMOVAL/INSTALLATION

W 6 U 9 1 7 W 2 1

1.  Turn  over the seaming welt. 

5.  Install  in the  reverse  order of  removal.

2.  Pull  the A-pillar trim to disengage clips A and  pin 

B from the body.

3.  Pull the A-pillar trim  upward to disengage  hook C 

from the  body.

4.  Pull the A-pillar trim  upward to disengage  hook D 

from the dashboard.

0 9 -1 7 -1 0

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов