Mazda MX-6 1998 Скачать руководство пользователя страница 700

Страница: 700 / 1282

TROUBLESHOOTING [LA4A-EL]

STEP

INSPECTION

ACTION

CHECK CONTINUITY OF TSS HARNESS
CIRCUIT

• Key off.

Caution

•

Do not pry on connector. Pull up on

harness.

• Disconnect TSS connector.
• Disconnect PCM. Inspect for damaged or

pushed out pins, corrosion, loose wires, etc.

• Install breakout box, leave PCM disconnected.
• Refer to connector schematic of TSS.

TSS Switch Connector Component

• Measure resistance between PCM test pin 84

at the breakout box and the TSS (+) circuit at

the TSS connector.

• Measure resistance between PCM test pin 91

at the breakout box and the TSS (-) circuit at

the TSS connector and chassis/battery ground.

• Is each resistance less than 5.0 ohms?

Yes

Go to next step.

Service open circuit.
Remove breakout box.
Reconnect all components.
Rerun OBD test.

CHECK TSS CIRCUIT FOR SHORT TO POWER

AND GROUND

• Key off.

• Disconnect TSS connector.

• Breakout box installed, PCM disconnected.
• Measure resistance between PCM test pins

84, 91 and test pins 71/97 at breakout box.

• Measure resistance between PCM test pins

84, 91, 71/97 and test pins 77/103 at breakout
box.

• Is each resistance greater than 10,000 ohms?

Yes

Go to next step.

Service short circuit.

Remove breakout box.
Reconnect all components.
Rerun OBD test.

TSS FUNCTIONAL TEST

Caution

•

Do not pry on connector. Pull up on

harness.

•   Disconnect vehicle harness at TSS.
•   Install transaxle tester on to TSS.
•   Connect voltmeter positive  lead to (+) TSS and

negative lead to (-) TSS jacks. Set voltmeter to

20 volts AC.

• Perform drive cycle test. Monitor voltmeter.
• Does the voltage increase with an increase in

vehicle speed?

Yes

Replace PCM.

Go to next step.

CHECK RESISTANCE OF TSS

Note

• Refer to the LA4A-EL Transaxle tester for

terminal locations.

• Connect ohmmeter negative lead to +TSS jack

and positive lead to -T S S jack on tester. This

is to test TSS.

•

Record resistance.

• Is the resistance between 140— 290 ohms?

Yes

Go to next step.

Replace TSS.
Rerun TSS functional test.

0 5 -0 1 A -2 5

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды

Mazda MX-6 1998, Руководство по ремонту

Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды