Mazda MX-6 1998 Скачать руководство пользователя страница 383

Страница: 383 / 1282

TROUBLESHOOTING [ENGINE CONTROL KL]

Fuel Pressure Hold Inspection

Idle Air Control Valve Inspection

1. Start the engine and run it at idle.

2. Disconnect the IAC valve connector and verify if

the engine speed drops or engine stalls.

3. If engine speed does not drop or does not stall,

check followings.

•

Check IAC valve. (Refer to 01-13 IDLE AIR
CONTROL VALVE INSPECTION.)

•

Check IAC valve air passage.

•

Check open or short circuit between IAC valve
and PCM.

4. Warm up the engine to normal operating

temperature and run it at idle.

5. Turn the electrical loads ON and verify that the

engine speed is within the specification.

Load condition

Idle speed

No load

550— 750

A/C ON

675— 975

P/S O N *1

550— 750

E/L ON*2

550— 750

*1 : Steering wheel fully turned.

*2 : When all of the following electrical loac conditions are

met, but other condition’s idle speed is the same as a no
load condition.

•   Headlight
•   Cooling fan
•   Blower motor
•   A/C switch and fan switch  ON

Note

•

Excludes temporary idle speed drop
immediately after the electrical loads are

turned ON.

6. If not as specified, check the related switches and

wiring harnesses.

Warning

•

Fuel line spills and leaks are dangerous.

Fuel can ignite and cause serious injuries

or death and damage. Fuel can also irritate

skin and eyes. To prevent this, always

complete the “BEFORE REPAIR

PROCEDURE” and “AFTER REPAIR

PROCEDURE” (Refer to 01-14 BEFORE

REPAIR PROCEDURE, 01-14 AFTER

REPAIR PROCEDURE).

1. Disconnect the negative battery cable.

2. Install a fuel pressure gauge between the fuel filter

and the main fuel hose. (Install clamps as shown.)

PRESSURE GAUGE

)

INSTALL CLAMPS

W6U101WHS

3. Disconnect the negative battery cable.
4. Remove the fuel pump relay.

Caution
•

Connecting the wrong fuel pump relay

socket terminals may possibly cause a

malfunction. Carefully connect the

specified terminals only.

5. Connect fuel pump relay socket terminal 30 and

87 by using a jumper wire.

FUEL PUMP
RELAY

W 6 U 1 0 1 W K K

0 1 -0 1 B -1 7 7

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды

Mazda MX-6 1998, Руководство по ремонту

Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды