Mazda MX-6 1998 Скачать руководство пользователя страница 1081 | Manualshive

Страница: 1081 / 1282

background image

TROUBLESHOOTING [WIPER/WASHER SYSTEMS]

Washer does not operate (Wipers operate)

TROUBLESHOOTING HINTS

Malfunction in windshield wiper and washer switch input signal circuit

0 W asher does not operate

• W indshield wiper and washer switch malfunction
• Malfunction in wiring harness between windshield wiper and washer switch and windshield washer motor

Malfunction in windshield washer motor operation circuit

© Washer does not operate

• W indshield washer motor malfunction
• Malfunction in wiring harness between windshield washer motor and ground

STEP

INSPECTION

ACTION

Remove column cover.
Remove windshield w iper and washer switch

without disconnecting windshield wiper and
washer switch connector.
Turn ignition switch to ON.
Turn windshield washer switch on.

Measure voltage at terminal G at windshield

wiper and washer switch connector of wiring

harness.
Is voltage

B+?

W 6 U 9 0 1 W Q 3

Yes

Go to next step.

No

Replace windshield wiper and washer switch.

Partially peel off right side mud guard.

Turn windshield washer switch on.

Measure voltage at terminal B at windshield

washer motor connector of wiring harness.

Is voltage

B+?

Yes

Go to next step.

No

Repair wiring harness between windshield wiper and

washer switch and windshield washer motor.

W 6 U 9 0 1 W Q 4

Inspect windshield washer motor.

c r 0 9 -1 9 WINDSHIELD WASHER MOTOR

INSPECTION

Is windshield washer motor okay?___________

Yes

Repair wiring harness between windshield washer motor

and ground.

No

Replace windshield washer motor.

0 9 -0 1 M -5

«
...
1079
1080
1081
1082
1083
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 8

Бренд: PAC Страницы: 5

Бренд: NavLinkz Страницы: 4

Бренд: Compass Страницы: 16

Бренд: ECS Electronics Страницы: 16

PACCAR PACMOBILE 20

Бренд: DAF Страницы: 18

Бренд: Alfa Romeo Страницы: 8

Бренд: Cadillac Страницы: 34

Бренд: Scion Страницы: 24

Бренд: Aries Страницы: 5

Бренд: Mercedes-Benz Страницы: 354

Бренд: r.LiNK Страницы: 21

Бренд: Paccar Страницы: 63

Бренд: Saturn Страницы: 440

Бренд: Kia Страницы: 58

CHALLENGER GK-6125A 2018

Бренд: Coolster Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды