Mazda MX-6 1998 Скачать руководство пользователя страница 587

Страница: 587 / 1282

REAR SUSPENSION

Piston rod nut

0 2 -1 3 FRONT SHOCK ABSORBER

REMOVAL/INSTALLATION, Piston Rod Nut
Removal Note

Mounting rubber

Upper spring seat

Coil spring

Installation Note

Dust cover

Bound stopper

Lower spring seat

Rear shock absorber

Coil Spring Installation Note

1. Temporarily install the coil spring, upper spring

seat, and mounting rubber on the shock absorber
as shown.

2. Mark the coil spring, upper spring seat, and

mounting rubber for proper installation.

3. Align the marks of the coil spring and upper spring

seat. Protect the coil spring and upper seat spring

by using a piece of cloth, then set the SSTs.

4. Compress the coil spring by using the SSTs.

5. Install the shock absorber so that the lower end of

the coil spring is seated on the step of the lower

spring seat.

6. Align the marks of the coil spring and the

mounting rubber.
Install the mounting rubber and piston rod nut,

then remove the

SSTs.

Piston rod nut tightening torque

90—137 N m {9.1— 14.0 kgf-m, 66— 101 ftlb f)

REAR SHOCK ABSORBER INSPECTION

•

Inspect the  rear shock absorber in the  same
manner as the front shock absorber.  (Refer to
0 2 -1 3   FRONT SHOCK ABSORBER
INSPECTION.)

REAR SHOCK ABSORBER DISPOSAL

W 6 U 2 1 4 W 0 3

•

Dispose the rear shock absorber in the same
manner as the front shock absorber. (Refer to

02 -1 3 FRONT SHOCK ABSORBER DISPOSAL.)

W 6 U 2 1 4 W A 2

0 2 -1 4 -2

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды

Mazda MX-6 1998, Руководство по ремонту

Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды