background image

REFRIGERANT SYSTEM

07-10 

REFRIGERANT SYSTEM

REFRIGERANT SYSTEM  SERVICE 

W A R N IN G S ............................................... 07-10-1

Using/Handling  Unapproved

R efrigerant............................................. 07-10-1

Handling  Refrigerant  ..............................07-10-1
Storing  R e frig e ra n t................................. 07-10-1

REFRIGERANT SYSTEM  SERVICE 

CAUTIONS  ............................................... 0 7-10-1

Handling  Compressor Oil 

...................... 07 -1 0 -1

REFRIGERANT SYSTEM  GENERAL

PRO C ED U R ES......................................... 0 7 -1 0 -2

Manifold  Gauge  Set  In s ta lla tio n

 

0 7 -1 0 -2

REFRIGERANT SYSTEM  PERFORMANCE

TEST  .........................................................  0 7 -1 0 -2

REFRIGERANT PRESSURE CHECK  . .   0 7 -1 0 -2

 

REFRIGERANT CHARGING  .................... 0 7 -1 0 -3

REFRIGERANT SYSTEM  SERVICE WARNINGS

Using/Handling  Unapproved  Refrigerant

•  

Using a flammable  refrigerant,  such  as OZ-12,

 

in this vehicle  is  dangerous.  In an  accident,

 

the  refrigerant may catch fire,  resulting  in

 

serious  injury or death.  When  servicing this

 

vehicle,  use only  R-134a.

•  

Checking for system  leaks on a vehicle that

 

has  been  serviced with flammable refrigerant,

 

such  as  OZ-12,  is  dangerous.  Conventional

 

leak detectors  use an  electronically generated

 

arc which  can  ignite the  refrigerant,  causing

 

serous  injury or death.  If a flammable

 

refrigerant  may  have been  used to  service the

 

system,  or  if you  suspect a flammable

 

refrigerant  has  been  used,  contact the  local

 

fire  marshall  or EPA  office for information  on

 

handling the  refrigerant.

W 6 U 7 1 0 W 0 1

Handling  Refrigerant
•  

Do  not allow the  refrigerant to  leak near fire or

 

any  kind  of heat.  A  poisonous  gas  may  be

 

generated  if the  refrigerant gas  contacts fire  or

 

heat such  as from  cigarettes and  heaters.
When  carrying out any  operation that  can

 

cause refrigerant leakage, extinguish  or

 

remove the above-mentioned  heat sources

 

and  maintain  adequate ventilation.

•  

Handling  liquid  refrigerant is dangerous.  A

 

drop  of  it on the  skin  can  result  in  localized

 

frostbite. When  handling the  refrigerant,  wear

 

gloves and  safety  goggles.  If  refrigerant

 

splashes  into the eyes,  immediately wash

 

them with  clean  water and  consult a  doctor.

Storing  Refrigerant
•  

The  refrigerant container is  highly

 

pressurized.  If  it  is  subjected to  high  heat,  it

 

could  explode,  scattering  metal fragments and

 

liquid  refrigerant that can  seriously  injure you.

 

Store the refrigerant at temperatures  below 40

 

°C  {104  °F}.

REFRIGERANT SYSTEM  SERVICE  CAUTIONS

Handling  Compressor Oil
•  

Use only S P -20 compressor oil for this

 

vehicle.  Using  PAG oil other than  S P -20

 

compressor oil can  damage the A/C

 

compressor.

•  

Do  not spill  S P -20 compressor oil  on the

 

vehicle.  A drop of compressor oil  on the

 

vehicle surface can  eat away at the  paint.  If oil

 

gets on the vehicle, wipe  it off  immediately.

•  

S P -20 compressor oil  (PAG oil)  has  a  higher
moisture absorption efficiency 

than 

the

 

previously  used  mineral  oil.  If moisture mixes

 

with the compressor oil, the  refrigerant

 

system  could  be damaged. Therefore,  install

 

caps  immediately after using the compressor

 

oil  or removing  refrigerant system  parts to

 

prevent moisture absorption.

W 6 U 7 1 0 W 0 2

0 7 -1 0 -1

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы: