Mazda MX-6 1998 Скачать руководство пользователя страница 241 | Manualshive

Страница: 241 / 1282

background image

TROUBLESHOOTING [ENGINE CONTROL KL]

STEP

INSPECTION

ACTION

6

CHECK  HEATED  OXYGEN  SENSOR
CIRCUIT  RESISTANCE
•   Key off.
•   PCM  connected to vehicle harness.
•   Connect suspected  heated oxygen sensor

connector.

•   NGS tester connected.
•   Key on,  engine off.
•   Access correct heated oxygen sensor PID.

• 0 2S 13 (Rear)

Note

• Heated oxygen sensor displayed as

0 2S 13 (Rear) on NGS tester.

DTC: P0142, P1143 and P1144 (H 02S

(Rear))

Test Pins: 61 and 97

•

Is voltage greater than 1.5 volts?

Yes

Go to step 9.

No

Go to next step.

7

CHECK RESISTANCE OF HEATED OXYGEN
SENSOR  GROUND  CIRCUIT  IN THE  PCM
•   Key off.
•   PCM connected to breakout box.  Vehicle

harness disconnected from breakout box.

• Measure resistance between Test Pin 91

and Test Pin 24 and 103 at breakout box.

• Is resistance reading less than 5.0

ohms?

Yes

REMOVE breakout box.
RECONNECT PCM.
Go to next step.

No

REPLACE  PCM.
REMOVE  breakout box.
RECONNECT all  components.
RESET  PCM to completely clear DTCs.

tr

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

8

APPLY  12  VOLTS TO  SUSPECT HEATED
OXYGEN  SENSOR  CIRCUIT
•   Key off.
•   Heated oxygen sensor (Rear)

disconnected.

• Jumper power to heated oxygen sensor

signal circuit at the vehicle harness
connector.

• Key on.
• Access heated oxygen sensor PID and

monitor.
• 0 2 S 13 PID

•

Is PID voltage greater than 1.5 volts?

Yes

REPLACE heated oxygen sensor.
RECONNECT all components.
RESET PCM to completely clear DTCs.

tr

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

No

RECONNECT all components.
Go to next step.

9

CHECK FOR OVER VOLTAGE ON THE

HEATED OXYGEN SENSOR CIRCUIT IN

THE  PCM
•   Key on.
•   PCM  connected to vehicle  harness.
•   Heated oxygen sensor disconnected.
•   Inspect both ends of connect for damaged

or pushed out pins, moisture, corrosion,
loose pins, etc. and service as necessary.

• Measure the voltage between Test Pin 91

at the heated oxygen sensor vehicle
harness connector and battery negative
post.

• Measure the voltage between heated

oxygen sensor signal Test Pin at the
heated oxygen sensor vehicle harness
connector and battery negative post.

•

Are voltage readings greater than 1.5

volts?

Yes

REPLACE PCM.

RECONNECT all components.

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

No

REPLACE heated oxygen sensor.
RECONNECT all components.
RESET PCM to completely clear DTCs.

n r

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

0 1 -0 1 B -3 5

«
...
239
240
241
242
243
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: Kargo Master Страницы: 13

Бренд: Kargo Master Страницы: 21

Бренд: Kargo Master Страницы: 4

Бренд: Yakima Страницы: 8

QuadraTop Adventure Top S

Бренд: Quadratec Страницы: 20

Бренд: Ironton Страницы: 7

Escalade ESV 2014

Бренд: Cadillac Страницы: 508

Бренд: Hama Страницы: 2

Бренд: Mercedes-Benz Страницы: 368

PRIME DESIGN VRR-NV200

Бренд: Safe Fleet Страницы: 12

v.LOGiC Intelligent Solution V5-NTG46

Бренд: Caraudio-Systems Страницы: 18

Бренд: PAC Страницы: 14

Бренд: Kolpin Страницы: 3

Бренд: AEM Страницы: 27

Бренд: TEINHOF Страницы: 2

Бренд: Prorack Страницы: 15

Бренд: Axxess Страницы: 4

TRUCK 2500 2017

Бренд: RAM Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды