Mazda MX-6 1998 Скачать руководство пользователя страница 319 | Manualshive

Страница: 319 / 1282

background image

TROUBLESHOOTING [ENGINE CONTROL KL]

KOEO, KOER

P1474

DTC

P1479

Cooling fan control primary circuit malfunction

Condenser fan control primary circuit malfunction

DESCRIPTION

• DTC P1474 indicates cooling fan control primary circuit failure.

• DTC P1479 indicates condenser fan circuit control primary failure.

[Possible Cause]

• Open or shorted fan, cooling fan control signal or

• Damaged fan relay (cooling fan or condenser fan)

condenser fan control signal circuit

• Damaged PCM

• Open power circuit to fan relay

STEP

INSPECTION

ACTION

1

CHECK FOR POWER CIRCUIT TO
APPLICABLE FAN RELAY

Note

• During diagnosis, use chart below to

determine correct pin  number,  circuit and
relay being tested.
•   DTC  P1474=PCM terminal 45
•   DTC  P1479=PCM terminal  17

•   Key off.
•   Disconnect appropriate fan  relay.
•   Key on.
•   Measure voltage  between power circuit at

applicable fan relay vehicle harness
connector and battery negative post.

•

Is voltage greater than 10.5 volts?

Yes

Go to next step.

No

SERVICE open power circuit to applicable fan relay.

RECONNECT fan relay.
RERUN OBD Test.

2

CHECK  FOR  COOLING  FAN  CONTROL
SIGNAL  OR  CONDENSER  FAN  CONTROL
SIGNAL  CIRCUIT CYCLING
•   Key on,  engine off.
•   Applicable fan  relay disconnected.
•   NGS tester connected.
•   Access Output Test Mode.
•   Connect non-powered test lamp between

power circuit and cooling fan control signal
or condenser fan control signal circuit at
applicable fan relay vehicle harness
connector.

• W hile observing test lamp, command

appropriate cooling fan speed on and off.

•

Does test lamp turn on and off when

cooling fan output is commanded on

and off?

Yes

Key off.

REPLACE appropriate fan relay.
RERUN OBD Test.

No

REPEAT test step to VERIFY results.
It test lamp still does not turn on and off as expected, turn
key off.
REMOVE test lamp.
Go to next step.

3

CHECK COOLING  FAN  CONTROL SIGNAL
OR  CONDENSER  FAN  CONTROL SIGNAL
CIRCUIT  FOR  SHORT TO  POWER  CIRCUIT
•   Key off.
•   Applicable fan  relay disconnected.
•   Disconnect  PCM.  Inspect for damaged or

pushed out pins, corrosion and loose wires.
Service as necessary.

• Key on, engine off.
• Measure voltage between cooling fan

control signal or condenser fan control
signal circuit at applicable fan relay vehicle

harness connector and battery negative

post.

• Key off.

• Was voltage less than 1.0 volt?

Yes

Go to next step.

No

SERVICE cooling fan control signal or condenser fan
control signal circuit short to power.
RECONNECT all components.
RERUN OBD Test.

01-01B -113

«
...
317
318
319
320
321
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: Camcar Страницы: 6

Бренд: Metra Electronics Страницы: 14

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 8

Бренд: PAC Страницы: 5

Retrotech RTX-68D-CHG

Бренд: Dakota Digital Страницы: 4

Бренд: Kia Страницы: 54

Ride-Rite Air Helper Springs 2173

Бренд: Firestone Страницы: 4

Бренд: Brodit Страницы: 2

Бренд: Axxess Страницы: 8

Бренд: Dodge Страницы: 276

Бренд: Westin Страницы: 3

Бренд: Acura Страницы: 6

Crossland X 2017

Бренд: Vauxhall Страницы: 245

Бренд: Horn Tools Страницы: 12

Бренд: Chevrolet Страницы: 324

Black Bison Sports Series

Бренд: Wald Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды