CONTROL SYSTEM [KL]
T e rm in a l v o lta g e (R e fe re n c e )
Term inal
S ignal
C on n ectio n
Test c o n d itio n
Voltage (V) P ossible m a lfu n c tio n
1
Shift solenoid B
(ATX)
Solenoid body
ON
B+
• Solenoid body
• Related harness
OFF
Below 1.0
2
MIL
Malfunction
indicator lamp
Malfunction indicator lamp OFF
B+
• MIL
• Related harness
Malfunction indicator lamp ON
Below 1.0
3
—
—
—
—
—
4
—
—
—
—
—
5
Communication
(Immobilizer)
Immobilizer unit
Check the signal by using an
oscilloscope
—
• PCM’
• Immobilizer unit
• Related harness
6
Transaxle range
position (D range)
(ATX)
Transaxle range
switch (D range)
Ignition switch
ON
D range
B+
• Transaxle range
switch
• Related harness
Other
Below 1.0
7
Transaxle range
position (1 range)
(ATX)
Transaxle range
switch (1 range)
Ignition switch
ON
1 range
B+
• Transaxle range
switch
• Related harness
Other
Below 1.0
8
Cylinder
identification (-)
Camshaft position
sensor
Ignition switch ON
Below 1.0
• Camshaft position
sensor
• Related harness
Idle
Below 1.0
9
Transaxle range
position (2 range)
(ATX)
Transaxle range
switch (2 range)
Ignition switch
ON
2 range
B+
• Transaxle range
switch
• Related harness
Other
Below 1.0
10
Blower
Fan switch
Iqnition switch
ON
Fan switch
OFF or at 1st
or 2nd
Approx.
10
• Fan switch
• Related harness
Fan switch ON
at 3rd or higher
Below 1.0
11
Torque reduction
(request)
Instrument cluster,
ABS/TCS CM
Ignition switch ON
Approx.
10
• ABS/TCS control
module
• Related harness
Idle
B+
12
—
—
—
—
—
13
EP ROM flashing
Data link connector
Ignition switch ON
Approx.
0.6
• PCM
• Related harness
Idle
Approx.
0.6
14
DRL
DRL unit
Daytime running light ON
Below 1.0
• DRL unit
• Related harness
Daytime running light OFF
Approx.
8.0
15
Diagnostic trouble
code output
Data link connector
terminal B U S -
Carry out inspection according to
diagnostic trouble code
Diagnostic trouble code output is
a part of serial communication
Judgment by terminal voltage is
not possible
—
• On-board
diagnostic system
• Related harness
16
Diagnostic trouble
code output
Data link connector
terminal BUS+
Carry out inspection according to
diagnostic trouble code
Diagnostic trouble code output is
a part of serial communication
Judgment by terminal voltage is
not possible
—
• On-board
diagnostic system
• Related harness
17
Condenser fan
control
Condenser fan
relay
Condenser fan stops
B+
• Condenser fan
relay
• Related harness
Condenser fan operation
Below 1.0
18
CDCV control
CDCV
Ignition switch ON
B+
• CDCV
• Related harness
Diagnosis executed
Below 1.0
19
Pressure regulator
control
PRC solenoid
valve
Idle (Hot condition)
Below 1.0
• PRC solenoid
valve
• Related harness
Other
B+
0 1 -4 0 B -4
Содержание MX-6 1998
