Mazda MX-6 1998 Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 1282

background image

TROUBLESHOOTING [ENGINE CONTROL FS]

STEP

INSPECTION

ACTION

5

CHECK  MAF CIRCUIT  FOR  SHORT TO
GROUND  IN  PCM
•   Key off.
•   MAF sensor disconnected.
•   Breakout box installed.
•   Reconnect PCM to breakout box.

• Disconnect NGS tester from DLC.

• Measure resistance between Test Pin 88

and Test Pins 36 and 24 or 103 at breakout
box.

•

Is each resistance greater than 10,000

ohms?

Yes

RECONNECT NGS tester.

Go to next step.

No

MAF sensor signal circuit shorted to ground or PCM

ground in PCM.

REMOVE breakout box.
RECONNECT MAF sensor.
RESET PCM to completely clear DTCs.

c r After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

6

CHECK PCM GROUND CIRCUIT (BETWEEN

PCM AND MAF SENSOR GROUND
CIRCUIT) FOR SHORT TO GROUND

CIRCUIT IN PCM

• Key off.
• MAF sensor disconnected.

• Breakout box installed.

•   PCM  connected to breakout box.
•   NGS disconnected from  DLC.
•   Measure resistance  between Test Pin  36

and Test Pins 51 or 103 at breakout box.

•

Is resistance greater than 10,000 ohms?

Yes

RECONNECT NGS tester.

Go to next step.

No

PCM  ground circuit shorted to ground circuit in  PCM.
REPLACE  PCM.
REMOVE breakout box.
RECONNECT all components.
RERUN  OBD Test.

7

CHECK MAF SENSOR  CIRCUIT OUTPUT
•   Key off.
•   MAF sensor connected.
•   Breakout box installed.
•   PCM connected.
•   Key on,  engine  running.

Note

• If idle is not stabilized at minimum of 700

rpm, go to ENGINE SYMPTOM

TROUBLESHOOTING.

• Measure voltage between Test Pin 88 at

breakout box and battery negative post.

•

Is voltage between

0.34

and 1

.96

volts at

idle?

Yes

MAF SIG to PCM is okay.
Go to next step.

No

MAF sensor signal circuit or MAF sensor ground circuit is
open or MAF SIG is shorted to MAF RTN in MAF sensor.

REPLACE  MAF sensor.
REMOVE breakout box.
RECONNECT  PCM.
RESET  PCM to completely clear DTCs.

c r After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

8

VERIFY MAF SENSOR  CIRCUIT  INPUT AND
OUTPUT
•   Key off.
•   MAF sensor connected.
•   Breakout box installed.
•   PCM  connected.
•   Key on,  engine  running.
•   Measure voltage between Test  Pin 88 and

Test Pin 36 at breakout box.

•

Is voltage between

0.34

and 1

.96

volts?

Yes

PCM ground circuit in MAF sensor is okay.
Go to next step.

No

PCM ground circuit open  in  MAF sensor.
REPLACE  MAF sensor.
REMOVE  breakout box.
RECONNECT  PCM.
RESET  PCM to completely clear DTCs.

c r After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

9

CHECK  MAF SENSOR  CIRCUIT OUTPUT
WITH  NGS TESTER
•   Key off.
•   MAF sensor connected.
•   Key on,  engine running.
•

Access MAF

V

PID with NGS tester at idle.

•

Is

MAF

V

PID between

0.34

and 1

.96

volts?

Yes

Unable to identify fault at this time.
Check possible intermittent.
Go to SYMPTOM TROUBLESHOOTING No.27.

No

MAF sensor signal circuit or PCM ground circuit is open or
shorted together in PCM.

REPLACE  PCM.
REMOVE  breakout box.
RECONNECT  PCM.
RESET  PCM to completely clear DTCs.

j y After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

0 1 -0 1 A -91

«
...
117
118
119
120
121
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

RadioPRO 5 RP5-GM41

Бренд: PAC Страницы: 3

Бренд: Ultra Start Страницы: 8

Бренд: Metra Electronics Страницы: 4

REARSIGHT OnStar 250-8822

Бренд: Rostra Страницы: 2

Бренд: FORM FIT Страницы: 2

Бренд: Prorack Страницы: 14

Бренд: Ironton Страницы: 7

Ferrari 360 Map Carbon Light

Бренд: MAcarbon Страницы: 4

Бренд: BMW Страницы: 38

Бренд: Yakima Страницы: 12

Бренд: FALCON RIDGE Страницы: 6

Бренд: Aries Страницы: 5

Бренд: Mercedes-Benz Страницы: 354

Бренд: AL-KO Страницы: 40

Бренд: Kia Страницы: 233

Бренд: Mercedes-Benz Страницы: 585

Бренд: Goobay Страницы: 2

2013 Zafira Tourer

Бренд: Vauxhall Страницы: 289

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды