AUTOMATIC TRANSAXLE [GF4A-EL]
A
B
4. If not as specified, replace the selector lever knob
component. (Refer to 0 5 -1 7B O/D OFF SWITCH
REMOVAL/INSTALLATION [GF4A-EL].)
5. If the switch is OK, check the wiring harness. (O/D
OFF switch— powertrain control module, O/D OFF
switch— Body ground.)
6. Install the front console. (Refer to 09-17 FRONT
CONSOLE REMOVAL/INSTALLATION.)
7. Connect the negative battery cable.
W 6 U 5 1 7 W D 2
■EL]
W 6 U 5 1 7 W 3 6
Tightening torque
2.0—2.9 N m {20— 30 kgf cm, 18— 26 in lbf}
O/D OFF SWITCH REMOVAL/INSTALLATION [GF4A
1. Disconnect the negative battery cable.
2. Remove the front console. (Refer to 09-17
FRONT CONSOLE REMOVAL/INSTALLATION.)
3. Remove the indicator panel installation screws.
(Refer to 05 -1 8 SELECTOR LEVER
DISASSEMBLY/ASSEMBLY.)
4. Disconnect the connector and remove the O/D
OFF switch terminals.
5. Remove the selector lever knob component.
6. Install a new selector lever knob component.
7. Install the O/D OFF switch terminals and connect
the connector.
8. Install the indicator panel installation screws.
(Refer to 05-18 SELECTOR LEVER
DISASSEMBLY/ASSEMBLY.)
9. Install the front console. (Refer to 0 9 -1 7 FRONT
CONSOLE REMOVAL/INSTALLATION.)
10. Connect the negative battery cable.
TRANSAXLE RANGE SWITCH INSPECTION [GF4A-EL]
Inspection of Operation
1. Verify that the starter operates only with the
ignition switch at the START position and the
selector lever in P and N positions.
2. Verify that the back-up lights illuminate when
shifted to R position with the ignition switch in the
ON position.
3. Check the transaxle range switch if not as
specified.
Inspection of Continuity
1. Disconnect the negative battery cable.
2. Remove the resonance chamber, fresh-air duct,
and air cleaner component. (Refer to 0 1 -1 3B
INTAKE-AIR SYSTEM
REMOVAL/INSTALLATION [KL].)
3. Disconnect the transaxle range switch connector.
4. Check continuity of the transaxle range switch.
0
Q : Continuity
Position/
Range
Connector terminal
A
B
c
D
E
F
G
H
I
P
Vs
J—
W
R
_/~'l
\J—
N
—o
_r\
{J—
D
O - - O
2
1
r\_
W 6 U 5 1 7 W 1 8
5. If not as specified, replace or adjust the transaxle
range switch.
6. Connect the transaxle range switch connector.
7. Install the air cleaner component, fresh-air duct,
and resonance chamber. (Refer to 01-13B
INTAKE-AIR SYSTEM
REMOVAL/INSTALLATION [KL].)
8. Connect the negative battery cable.
W 6 U 5 1 7 W F 5
0 5 -1 7 B -1 1
Содержание MX-6 1998
