Mazda MX-6 1998 Скачать руководство пользователя страница 1062 | Manualshive

Страница: 1062 / 1282

background image

TROUBLESHOOTING [INTERIOR LIGHTING SYSTEM]

When interior light switch is at DOOR, interior light does not illuminate (When interior light switch is at ON,

interior light illuminates)

TROUBLESHOOTING HINTS

Malfunction in interior light tim er operation circuit

© Interior light does not illuminate

•   Interior light malfunction
•   CPU  malfunction
•   Door switch  malfunction
•   Malfunction  in wiring  harness between CPU  and door switch

STEP

INSPECTION

ACTION

Remove driver’s side front scuff plate.
Remove driver’s side front side trim.
Remove nut fixed in joint box and remove
CPU from joint box.

Set interior light switch at DOOR.

Measure voltage at terminal 1F at joint box.
Is voltage

B+?

W 6 U 9 0 1 W N 1

Yes

Go to step 3.

No

Go to step 2.

Inspect interior light.

c r 0 9 -1 8 INTERIOR LIGHT INSPECTION

Is interior light okay?

Yes

Repair wiring harness between interior light and CPU.

No

Replace interior light.

tr

09-1 8 INTERIOR LIGHT REMOVAUINSPECTION

Inspect CPU.

tr

09—40 CPU INSPECTION

Is CPU okay?

Yes

Go to next step.

No

Replace CPU.

zt

0 9 -4 0 CPU REMOVAIVINSTALLATION

Open all doors.

Check for continuity between 11 at joint box

and door switch.

Is there continuity?

Yes

Go to next step.

No

Repair wiring harness between joint box and door switch.

W 6 U 9 0 1 W N 2

Inspect door switch.

c r 0 9 -1 8 DOOR SWITCH INSPECTION

Is door switch okay?

Yes

Replace CPU.

t r

0 9-40 CPU REMOVAL/INSTALLATION

No

Replace door switch.

tr

0 9-18 DOOR SWITCH REMOVAMNSTALLATION

0 9 -0 1 K -3

«
...
1060
1061
1062
1063
1064
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: Warrior Products Страницы: 4

AAB-P-RZR900-K2-001

Бренд: SuperATV Страницы: 3

Бренд: Subaru Страницы: 99

Бренд: EZTRUNK Страницы: 3

Ride-Rite Air Helper Springs 2173

Бренд: Firestone Страницы: 4

Бренд: Metra Electronics Страницы: 8

Q Access Alpha GSE 2023

Бренд: Q Mobility Group Страницы: 9

2005 JR41 Stratus

Бренд: Dodge Страницы: 293

S90 - ACCESSORY PANEL

Бренд: Volvo Страницы: 166

Бренд: Oldsmobile Страницы: 248

2010 Accord Coupe

Бренд: Honda Страницы: 410

Бренд: Pogo Страницы: 40

Бренд: ideus Страницы: 116

Бренд: Roadefend Страницы: 15

Бренд: LaserLine Страницы: 4

Бренд: Nav TV Страницы: 8

Бренд: Falcon Страницы: 36

Бренд: SAF-HOLLAND Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды