Mazda MX-6 1998 Скачать руководство пользователя страница 962 | Manualshive

Страница: 962 / 1282

background image

TROUBLESHOOTING [AIR BAG SYSTEM]

STEP

INSPECTION

ACTION

9*

Disconnect SAS unit connector (21-pin) and

instrument cluster connector (12-pin).
Check for continuity between terminal Q at
SAS unit connector (21-pin) of wiring harness
and terminal 11 at instrument cluster connector
(12-pin) of wiring harness.

Is there continuity?

W 6 U 8 0 1 W A V

Yes

Replace SAS unit, then go to step 10.

o r 0 8 -1 0 SAS UNIT REMOVAL/INSTALLATION

No

Replace or repair wiring harness between instrument

cluster and SAS unit, then go to step 10.

10

Connect SAS unit connector.
Connect instrument cluster connector.
Connect negative battery cable.

When turning ignition switch to ON, does air

bag system warning light operate properly?

Yes

Troubleshooting completed.

No

Reconfirm symptoms of malfunction.

Air bag system warning light illuminates immediately after ignition switch is turned to ON and remains

illuminated

TROUBLESHOOTING HINTS

Malfunction in air bag system warning light circuit

© A ir bag system warning light remains illuminated

SAS  unit malfunction
Malfunction  in short bar between terminal Q of  SAS unit connector (21-pin)  and terminal S of SAS  unit connector
(21-pin)
Battery malfunction or battery charge/discharge system  malfunction
Poor connection of SAS unit connector (21-pin)
Malfunction in wiring  harness between  instrument cluster and SAS unit

STEP

INSPECTION

ACTION

Measure battery positive voltage.

Is voltage

more than 9 V?

Yes

Go to next step.

No

Inspect engine charging system.

tr

01-01 ENGINE SYMPTOM TROUBLESHOOTING

Turn ignition switch to LOCK.

Disconnect negative battery cable and wait for

more than 1 minute

to allow the backup

power supply of SAS unit to deplete its stored
power.

Remove rear console.

C 7 -

0 9 -1 7 REAR CONSOLE

REMOVAL/INSTALLATION

Remove the driver-side side wall.
Is terminal Q of SAS unit connector (21-pin)

securely connected with connector?

Yes

Go to next step.

No

Reconnect properly, then go to step 6.

W6U801WAQ

0 8 -0 1 A - 1 2

«
...
960
961
962
963
964
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: AAMP of America Страницы: 6

Бренд: iDataLink Страницы: 9

Бренд: Daihatsu Страницы: 485

Бренд: Yakima Страницы: 8

Бренд: GARO Страницы: 2

Бренд: Taffio Страницы: 8

Бренд: Metra Electronics Страницы: 2

Calispace Ocean 80

Бренд: Calitop Страницы: 5

Бренд: M7 SPEED Страницы: 6

Бренд: Fast Master Products Страницы: 13

XEBRA ZAPCAR Series

Бренд: Zap Страницы: 16

Parktronic system Volkswagen Golf MK7

Бренд: Car-Systems Страницы: 10

Бренд: ULTIMATE SPEED Страницы: 40

Бренд: Cadillac Страницы: 2

Бренд: Buick Страницы: 20

Telescoping Computer Base C-TCB-34

Бренд: Havis-Shields Страницы: 1

Бренд: PEUGEOT Страницы: 107

Бренд: Lincoln Страницы: 538

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды