Mazda MX-6 1998 Скачать руководство пользователя страница 996 | Manualshive

Страница: 996 / 1282

background image

TROUBLESHOOTING [POWER OUTSIDE MIRROR]

3

Right power outside mirror does not operate vertically or horizontally (Left power outside mirror operates)

TROUBLESHOOTING HINTS

Malfunction in power outside mirror switch input signal circuit

© Right power outside mirror does not operate

• Power outside mirror switch malfunction
• Malfunction in wiring harness between power outside mirror switch and right power outside mirror

Malfunction in power outside mirror operation circuit

© Right power outside mirror does not operate

• Right power outside mirror malfunction

STEP

INSPECTION

ACTION

Remove power outside mirror switch without

disconnecting power outside mirror switch
connector.

Turn ignition switch to ACC.
Turn power outside mirror switch to right side

position and turn it to left or to down position.
Measure voltage at terminal F at power
outside mirror switch connector of wiring
harness.
Is voltage

B+?

W 6 U 9 0 1 W C 5

Yes

Go to next step.

No

Replace power outside mirror switch.

Remove passenger’s side front door trim.
Partially peel off passenger’s side front door

screen.
Turn  ignition switch to ACC.
Turn power outside mirror switch to  right side
position  and turn it to left or to down position.
Measure voltage at terminal  D at right power
outside mirror connector of wiring harness.

Is voltage

B+?

Yes

Replace right power outside mirror.

No

Repair wiring harness between power outside mirror

switch and right power outside mirror.

W 6 U 9 0 1 W C 6

0 9 -0 1 C -4

«
...
994
995
996
997
998
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: Happy Orange Страницы: 2

Бренд: Acdeos Страницы: 38

Бренд: JETBAG Страницы: 44

BLACK STEEL S2560

Бренд: Fab Fours Страницы: 9

Бренд: Kia Страницы: 419

Бренд: Velleman Страницы: 6

Stratus LHD 1997

Бренд: Chrysler Страницы: 1534

Бренд: Condor Страницы: 2

Бренд: Motoalliance Страницы: 8

Бренд: AA Products Страницы: 6

DELTA DL FIX 209FP

Бренд: Menabo Страницы: 8

Truck Training Model

Бренд: WABCO Страницы: 56

Бренд: Fab Fours Страницы: 21

Бренд: Cadillac Страницы: 529

Бренд: Toro Страницы: 16

Бренд: Lexus Страницы: 830

Бренд: TomTom Страницы: 22

Бренд: Toyota Страницы: 285

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды