manualshive.com logo in svg

Mazda MX-6 1998, Руководство по ремонту, Страница: 483 / 1282

Поделиться
Скачать
Mazda MX-6 1998 Скачать руководство пользователя страница 483

EXHAUST SYSTEM

8

Heated oxygen sensor (Front (California only))

9

Exhaust manifold insulator

10

Exhaust manifold

EXHAUST SYSTEM  REMOVAL/INSTALLATION  [KL]

W 6 U 1 1 5 W 5 2

Warning
•  

When the engine and exhaust system  are  hot, they  can  badly  burn.  Turn  off the engine and  wait

 

until they are cool  before removing  or  installing the exhaust system.

1.  Disconnect the  negative  battery cable.

2.  Remove  in the order indicated  in the table.

3.  Install  in the  reverse order of  removal.

1

Main silencer

2

Presilencer

3

Heated oxygen sensor (Rear)

4

Three way catalytic converter

5

Heated oxygen sensor (Middle)

6

Front pipe

7

Heated oxygen sensor (Front  RH)

8

Heated oxygen sensor (Front LH)

9

Exhaust manifold insulator

10

Exhaust manifold

0 1 -1 5 -2

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов