Mazda MX-6 1998 Скачать руководство пользователя страница 44

Страница: 44 / 1282

TROUBLESHOOTING [ENGINE CONTROL FS]

Note

•

D T C P 0 1 0 3

could be generated by foreign material blocking the mass air flow sensor screen causing an

air flow restriction. If contaminants are found on the screen, check air filter installation in air cleaner tray
and proper sealing of

a ir

cleaner

a n d a ir

tube before

p ro c e e d in g . R e ru n

OBD

T est a fte r repair.

DTC

P0106

EGR boost sensor circuit input signal out of self-test range

DESCRIPTION

• DTC P0106 indicate EGR boost sensor input signal is out of self-test range

[Possible Cause]

• Damaged EGR boost sensor

• Damaged EGR boost solenoid valve

• Damaged EGR boost solenoid valve to EGR boost

sensor hose

•   Damaged  PCM
•   Damaged harness connector
•   Damaged harness

STEP

INSPECTION

ACTION

CHECK EGR BOOST SENSOR CONSTANT
VOLTAGE

Note

• If DTC P1410 is present confirm that PRC

solenoid valve and EGR boost solenoid

valve harness connectors are not

swapped.

Yes

Go to next step.

•   Key on,  engine off.
•   EGR  boost sensor disconnected.
•   Measure voltage between constant voltage

and ground circuits at EGR boost sensor

vehicle harness connector.

• Key off.

• Is voltage between 4.0 and 6.0 volts?

REPAIR open in constant voltage circuit.

CHECK CONTINUITY OF EGR BOOST
SENSOR HARNESS CIRCUITS

• Key off.

• EGR boost sensor disconnected.
• Disconnect PCM. Inspect for damaged or

pushed out pins, corrosion, loose wires,

Yes

Go to next step.

etc. Service as necessary.

• Install breakout box. Leave PCM

disconnected.

• Measure the resistance between EGR

boost signal circuit at EGR boost sensor

vehicle harness connector and Test Pin 34

at breakout box.

• Measure the resistance between ground

circuit at EGR boost sensor vehicle
harness connector and Test Pin 91 at
breakout box.

•

Is each resistance less than 5 ohms?

Service open in appropriate circuit.
EGR boost sensor harness circuit.

RESET PCM to completely clear DTCs.

¡¡y

After Repair Procedure

COMPLETE OBD II Drive Mode.
Confirm repair by performing EGR portion of OBD II Drive
Mode to check for DTCs.

CHECK EGR BOOST SIGNAL CIRCUITS

FOR SHORT TO GROUND AND POWER

•   Key off.
•   EGR  boost sensor disconnected.
•   Breakout box installed.  PCM  disconnected.
•   Measure  resistance between Test  Pin 34

and Test Pins 91 RTN, 51 and 103 at
breakout box.

• Measure resistance between Test Pin 34

and Test Pins 71, 90 and 97 at breakout
box.

•

Is resistance greater than 10,000 ohms?

Yes

Go to next step.

SERVICE short in EGR boost signal circuit.

REMOVE breakout box.
RECONNECT all components.
RESET PCM to completely clear DTCs.

After Repair Procedure

COMPLETE OBD II Drive Mode.
Confirm repair by performing EGR portion of OBD II Drive
Mode to check for DTCs.

0 1 -0 1 A -1 6

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды

Mazda MX-6 1998, Руководство по ремонту

Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды