manualshive.com logo in svg

Mazda MX-6 1998, Руководство по ремонту

Mazda MX-6 1998 Workshop Manual - руководство по ремонту и обслуживанию автомобиля. Скачайте бесплатно мануал на manualshive.com. Подробное описание всех работ и узлов автомобиля, что позволит вам самостоятельно проводить техническое обслуживание. Улучшите свой автомобиль с помощью нашего руководства.

Поделиться
Скачать
background image

ENGINE 

01

SECTION

01

TROUBLESHOOTING

 

[ENGINE  CONTROL FS]  . . . .   01-01A

 

TROUBLESHOOTING

 

[ENGINE CONTROL  KL]  . . . .   0 1 -01B

 

TROUBLESHOOTING  [CRUISE

CONTROL SYSTEM]  ............01-01C

MECHANICAL [FS]  ................. 01-10A
MECHANICAL [KL]  ................. 01 -10B

LUBRICATION  SY S TE M  

01-11

COOLING  S Y S T E M ................. 01-12
INTAKE-AIR  SYSTEM  [FS]  . . .   01-13A

 

INTAKE-AIR SYSTEM  [KL]  . . .   01 -1 3B

FUEL S Y S T E M ............................01-14

EXHAUST S Y S T E M ................. 01-15
EMISSION  SYSTEM  ................01-16

CHARGING  SYSTEM  ................ 01-17
IGNITION  SYSTEM  ....................01-18
STARTING  SYSTEM  .................. 01-19
CRUISE CONTROL SYSTEM  .  01-20
CONTROL SYSTEM  [ F S ]  

01-40A

CONTROL SYSTEM  [ K L ]  

01-40B

TECHNICAL DATA....................01-50
SPECIAL T O O L S ........................01-60

01 “ 01A  TROUBLESHOOTING  [ENGINE  CONTROL  FS]

FOREWORD  ........................................... 01 -0 1 A -2
ENGINE  ON-BOARD  DIAGNOSIS  [FS]  01-01 A -2

On-Board  Diagnostic  (OBD) Test

D escription......................................... 01-01 A -2

System  P a s s ....................................... 01-01 A -2

Key On  Engine Off  (KOEO)  Seif-Test  01-01 A -2  
Key On  Engine  Running  (KOER)

S e lf-T e st.............................................01-01 A -2

Read/Clear Continuous  Memory  DTC

Access  S e lf-T e st............................... 0 1 -0 1 A -2

Parameter Identification  (PID) Access  01-01 A -2
Brake On/Off T e s t............................... 01-01 A -2

Transaxle  Control  Switch Test  ..........01-01 A -2

Power Steering  Pressure  (PSP)  Switch

T e s t.....................................................01-01 A -2

On-Board  Diagnostic T e s t ..................01-01 A -2

Reading  DTCs  P ro ce d u re ..................0 1 -0 1 A -3
Read/Clear Continuous  DTC  Self-Test

Procedure  ......................................... 01 -0 1 A -4

Key ON  Engine OFF Self-Test

Procedure  ......................................... 01-01 A -4

Key ON  Engine  Running  Self-Test

Procedure  ......................................... 0 1 -0 1 A -5

After Repair Procedure  ..................... 01 -0 1 A -5

PID/DATA  Monitor and  Record

Procedure  ......................................... 01-01 A -5

Playback of Stored  PIDs  Procedure  .  01 -0 1 A -6

Output Test  Mode  P ro c e d u re  

01-01 A -6

Oxygen  Sensor Monitoring Test  Results 

Access  Procedure  ........................... 01-01 A -6

OBD  II  Drive  M o d e ............................... 0 1 -0 1 A -7

ENGINE  SYMPTOM  TROUBLESHOOTING

[ F S ] ......................................................... 01—01 A—122

Diagnostic  In d e x ................................. 0 1 -0 1 A -1 2 2

Quick  Diagnostic Chart  ......................0 1 -0 1 A -1 2 4

Description  of  Drivability  Problems  . .   0 1 -0 1 A - 1 26 
Fuel  Pressure  Release and  Servicing  Fuel

S y s te m ............................................... 01-01 A -1 26

Fuel  Line  Safety  Procedures  ............0 1 -0 1 A -1 2 6
Symptom Troubleshooting  ................0 1 -0 1 A -1 2 7

ENGINE  DIAGNOSTIC  INSPECTION

[ F S ] ......................................................... 01-01 A -1 69

Spark Plug  Condition  C h e c k .............. 01-01 A - 1 69

ENGINE  SYSTEM  INSPECTION  [FS]  .  0 1 -0 1 A -1 7 2

Intake  Manifold  Vacuum  Inspection  . .   0 1 -0 1 A -1 7 2  
Fuel  Injector Operation  Inspection  . . .   0 1 -0 1 A -1 7 2  
Idle Air Control  Valve  Inspection  ___ 01-01 A -1 73
Fuel  Pressure  Hold  In s p e c tio n .......... 01-01 A - 1 73
Fuel  Line  Pressure  Inspection  .......... 0 1 -0 1 A -1 7 4
Pressure  Regulator Control

Inspection  ......................................... 0 1 -0 1 A -1 7 5

Purge  Control  Inspection.................... 01-01 A - 1 76
Main  Relay Operation  Inspection___ 0 1 -0 1 A -1 7 6
Ignition  Timing  Control  Inspection  . . .   01-01 A -1 7 6

A/C  Cut Off Control  In sp e ctio n .......... 01-01 A -176

Spark Test  ........................................... 01-01 A -1 77
Fuel  Cut Control  Inspection  ..............01-01 A -1 77

Cooling  Fan  Control  System 

Inspection  ......................................... 01—01 A—177

01-01 A -1

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Hama Cup holder Operating Instruction preview
Cup holder
Бренд: Hama Страницы: 2
Abarth 124 SPIDER Service And Warranty Handbook preview
124 SPIDER
Бренд: Abarth Страницы: 36
Suzuki Movano Owner'S Manual preview
Movano
Бренд: Suzuki Страницы: 353
Torklift F2012 Installation Instructions Manual preview
F2012
Бренд: Torklift Страницы: 16
Phonocar VM350 Mounting Instructions preview
VM350
Бренд: Phonocar Страницы: 2
U.S. General 96524 Set Up And Operating Instructions Manual preview
96524
Бренд: U.S. General Страницы: 8
SAN HIMA SGBR015 Installation Instructions Manual preview
SGBR015
Бренд: SAN HIMA Страницы: 10
ULTIMATE SPEED 91449 Operation And Safety Notes preview
91449
Бренд: ULTIMATE SPEED Страницы: 34
Yakima LowRider Manual preview
LowRider
Бренд: Yakima Страницы: 15
Carcomm CMPC-22 Fujitsu-Siemens PocketLoox 410 Installation Manual preview
CMPC-22 Fujitsu-Siemens PocketLoox 410
Бренд: Carcomm Страницы: 2
Scosche MAGICGRIP MGQDWD-CPO Instructions Manual preview
MAGICGRIP MGQDWD-CPO
Бренд: Scosche Страницы: 12
Seat Toledo 2019 Owner'S Manual preview
Toledo 2019
Бренд: Seat Страницы: 300
Mazda 2014 CX-9 User Manual preview
2014 CX-9
Бренд: Mazda Страницы: 604
Honda 08P00-T7S-600 Installation Instructions preview
08P00-T7S-600
Бренд: Honda Страницы: 5
Jacob Jensen Electronic Parking Disc 3 User Manual preview
Electronic Parking Disc 3
Бренд: Jacob Jensen Страницы: 17
Camcar Walmec 40102 Manual preview
Walmec 40102
Бренд: Camcar Страницы: 6
BMW 330e Touring xDrive G21 2021 Owner'S Handbook Manual preview
330e Touring xDrive G21 2021
Бренд: BMW Страницы: 102
Chevrolet 2003 Malibu Owner'S Manual preview
2003 Malibu
Бренд: Chevrolet Страницы: 354

Бренды по названию

Популярные бренды

Загрузить еще бренды