manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

McBSP3

9-23

DSP Public Peripherals

DSP_Write(0x0000) => SPCR2; set up SPCR2 as initial configuration.

Note:

This setup is not needed after reset.

9.4.4.14

Pin Control Register Configuration

DSP_Write(0x0a0b) => PCR; set up PCR per below configuration.

Table 9–24. Pin Control Register Configuration (DSP_Write(0x0a0b) => PCR)

Bit

Config Value

Description

15–14

00b

Reserved

13

0b

Set serial port mode for DX, FSX and CLKX pins

12

0b

Set serial port mode for DR, FSR and CLKR pins

11

1b

TX frame-synchronization signal driven by internal generator

10

0b

RX frame-synchronization signal derived by external source

9

1b

McBSP is set master and generate clock by internal source

8

0b

CLKR set input pin and derived by external source

7

0b

Sample rate generator input clock mode bit

6

0b

CLKS pin status (no meaning in OMAP5910)

5

0b

DX pin status

4

0b

DR pin status

3

1b

Set FSX polarity as active high

2

0b

Set FSR polarity as active high

1

1b

Set CLKX polarity as data driven on falling edge

0

1b

Set CLKR polarity as data sampled on rising edge

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

D-Link DFE-690TXD Quick Install Manual preview
DFE-690TXD
Brand: D-Link Pages: 12
Mylex eXtremeRAID 1100 Installation Manual preview
eXtremeRAID 1100
Brand: Mylex Pages: 74
B&B Electronics Parallel & Serial Port Checker PPC User Manual preview
Parallel & Serial Port Checker PPC
Brand: B&B Electronics Pages: 4
Cypress Semiconductor CY7C1329H Specification Sheet preview
CY7C1329H
Brand: Cypress Semiconductor Pages: 16
Renesas R0E530650CFJ30 User Manual preview
R0E530650CFJ30
Brand: Renesas Pages: 4
AXAGO PCEU-43R Quick Installation Manual preview
PCEU-43R
Brand: AXAGO Pages: 2
DigiTech RPX400 Troubleshooting Manual preview
RPX400
Brand: DigiTech Pages: 6
Keithley DAS-1800HR Series User Manual preview
DAS-1800HR Series
Brand: Keithley Pages: 139
Dahua Technology NVR2104/2108HS-W-4KS2 1U User Manual preview
NVR2104/2108HS-W-4KS2 1U
Brand: Dahua Technology Pages: 363
Air Live AirVideo-100 Quick Setup Manual preview
AirVideo-100
Brand: Air Live Pages: 2
IEI Technology WAFER-EHL Series User Manual preview
WAFER-EHL Series
Brand: IEI Technology Pages: 142
RadioSPECTRAL ICOM IC-7300 Installation Manual preview
ICOM IC-7300
Brand: RadioSPECTRAL Pages: 2
ZALMAN VF2000 LED User Manual preview
VF2000 LED
Brand: ZALMAN Pages: 9
Amphenol C2LINX Series Installation Manual preview
C2LINX Series
Brand: Amphenol Pages: 43
AMC DSP 88 User Manual preview
DSP 88
Brand: AMC Pages: 28
ekwb 3831109819395 Manual preview
3831109819395
Brand: ekwb Pages: 10
SilverStone SDP12 Quick Start Manual preview
SDP12
Brand: SilverStone Pages: 2
ACTi GNR-410 Quick Installation Manual preview
GNR-410
Brand: ACTi Pages: 12

Brands by name

Popular brands

Load more brands