Texas Instruments OMAP5910 Technical Reference Manual Download | Manualshive

Page: 328 / 1209

background image

OMAP5910 Configuration Registers

6-37

MPU Private Peripherals

Table 6–35. Functional Multiplexing Control 7 Register (FUNC_MUX_CTRL_7)

Bits

Name

Description

R/W

Reset

Value

31–21

RESERVED

Reserved for future expansion. These bits must always
be written as 0.

R/W

0x0

20–18

CONF_ARMIO_2_R

These bits control the multiplexing on the OMAP5910
I/O, which defaults to MPUIO2 at reset

The control for this I/O is forced to 000 at reset and
while in compatibility mode.

R/W

0x0

17–15

CONF_ARMIO_4_R

These bits control the multiplexing on the OMAP5910
I/O, which defaults to MPUIO4 at reset

The control for this I/O is forced to 000 at reset and
while in compatibility mode.

R/W

0x0

14–12

CONF_ARMIO_5_R

These bits control the multiplexing on the OMAP5910
I/O, which defaults to MPUIO5 at reset.

The control for this I/O is forced to 000 at reset and
while in compatibility mode.

R/W

0x0

11–9

CONF_GPIO_0_R

These bits control the multiplexing on the OMAP5910
I/O, which defaults to GPIO0 at reset.

The control for this I/O is forced to 000 at reset and
while in compatibility mode.

R/W

0x0

8–6

CONF_GPIO_1_R

These bits control the multiplexing on the OMAP5910
I/O, which defaults to GPIO1 at reset.

The control for this I/O is forced to 000 at reset and
while in compatibility mode.

R/W

0x0

5–3

CONF_GPIO_2_R

These bits control the multiplexing on the OMAP5910
I/O, which defaults to GPIO2 at reset.

The control for this I/O is forced to 000 at reset and
while in compatibility mode.

R/W

0x0

2–0

CONF_GPIO_3_R

These bits control the multiplexing on the OMAP5910
I/O, which defaults to GPIO3 at reset.

The control for this I/O is forced to 000 at reset and
while in compatibility mode.

R/W

0x0

«
...
326
327
328
329
330
...
»

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

Brand: 3Com Pages: 8

Brand: LaCie Pages: 44

LaCie Ethernet Disk

Brand: LaCie Pages: 2

SATA II ExpressCard 34

Brand: LaCie Pages: 2

12big Rack Fibre 8

Brand: LaCie Pages: 9

Brand: Paradyne Pages: 112

Brand: Compaq Pages: 112

Armor 101 Series

Brand: Lochinvar Pages: 28

Armor 101 Series

Brand: Lochinvar Pages: 44

Brand: SUNRICH TECHNOLOGY Pages: 5

Brand: Roland Pages: 2

Brand: Realtek Pages: 30

Brand: RAK Pages: 30

Brand: Wintech Pages: 21

StorageWorks AIT 35GB AutoLoader

Brand: Compaq Pages: 4

Millennium P650

Brand: Matrox Pages: 54

Brand: Longshine Pages: 27

Procont LMC-008-IO

Brand: janitza Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands