manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

LCD Dedicated Channel

5-31

System DMA Controller

Table 5–8. IMIF LCD Register Settings—Two Frames (Continued)

DMA_LCD_CTRL

Register Settings

DMA_LCD_TOP_F1_L

0x0000

DMA_LCD_BOT_F1_U

0x000B

DMA_LCD_BOT_F1_L

0x00DE

DMA_LCD_TOP_F2_U

0x000C

DMA_LCD_TOP_F2_L

0x0000

DMA_LCD_BOT_F2_U

0x000C

DMA_LCD_BOT_F2_L

0x00DE

The transfer starts when the enable (hardware) signal from the LCD controller
is asserted high.

The transfer runs, and the interrupts are generated at the ends of frames 1
and 2.

Figure 5–12. LCD Dual-Frame Mode Transfer Scheme

IMIF

Video frame 1

LCD

controller

DMA

Video frame 2

0x0B 0000

0x0C 0000

0x0B 00DE

0x0C 00DE

When an interrupt occurs, read the DMA_LCD_CTRL register to find the
source of the interrupt.

If DMA_LCD_CTRL(3) = 1, end frame 1 interrupt.

If DMA_LCD_CTRL(4) = 1, end frame 2 interrupt.

When bottom of frame 1 is reached, the DMA loads the top frame 2 addresses.
When bottom of frame 2 is reached, the DMA loads the top frame 1 address.

Reset DMA_LCD_CTRL3 and 4 and wait for another interrupt.

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

Cabletron Systems Netlink FRX8000 Installation And Setup Manual preview
Netlink FRX8000
Brand: Cabletron Systems Pages: 94
Cabletron Systems MMAC-Plus 9E423-24 Reference Manual preview
MMAC-Plus 9E423-24
Brand: Cabletron Systems Pages: 10
Cabletron Systems MMAC-Plus 9A128-01 Management Manual preview
MMAC-Plus 9A128-01
Brand: Cabletron Systems Pages: 22
Cabletron Systems Spectrum EMM-E6 Addendum Manual preview
Spectrum EMM-E6
Brand: Cabletron Systems Pages: 2
Cabletron Systems DLM6C-AA Overview And Setup Manual preview
DLM6C-AA
Brand: Cabletron Systems Pages: 54
Cabletron Systems Cabletron BRIM-F6 User Manual preview
Cabletron BRIM-F6
Brand: Cabletron Systems Pages: 43
Cabletron Systems Netlink FRX4000 Maintenance Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 60
Cabletron Systems 9E132-15 Appendix preview
9E132-15
Brand: Cabletron Systems Pages: 8
Cabletron Systems TRXI-22 Addendum preview
TRXI-22
Brand: Cabletron Systems Pages: 4
F5 WANJet 500 Quick Start Card preview
WANJet 500
Brand: F5 Pages: 2
F5 ARX-500 Hardware Reference Manual preview
ARX-500
Brand: F5 Pages: 90
F5 ARX-4000 Parts Replacement Manual preview
ARX-4000
Brand: F5 Pages: 47
Delta M125HV-113 Quick Installation Manual preview
M125HV-113
Brand: Delta Pages: 2
IDT USB-BRIDGEV2-EVAL Evaluation Board Manual preview
USB-BRIDGEV2-EVAL
Brand: IDT Pages: 11
GarrettCom Industrial Network Track OSI Brochure preview
Industrial Network Track OSI
Brand: GarrettCom Pages: 10
Adaptec 2410SA - Serial ATA RAID Controller Hardware Installation Manual preview
2410SA - Serial ATA RAID Controller
Brand: Adaptec Pages: 14
Loopcomm LP-8014 Quick Start Manual preview
LP-8014
Brand: Loopcomm Pages: 2
Z-Wave IOMOD10F Hardware User Manual preview
IOMOD10F
Brand: Z-Wave Pages: 42

Brands by name

Popular brands

Load more brands