Texas Instruments OMAP5910 Technical Reference Manual Download Page 393

Page: 393 / 1209

MicroWire Interface

7-31

MPU Public Peripherals

Table 7–26. MicroWire Registers (Continued)

Register

Offset

Address

Size

R/W

Description

SR3

Setup 3

R/W

16 bits

FFFB:3000

0x10

SR4

Setup 4

R/W

16 bits

FFFB:3000

0x14

SR5

Setup 5

R/W

16 bits

FFFB:3000

0x18

Table 7–27. Transmit Data Register (TDR)

Bit

Name

Function

Reset

Value

15–0

Data to transmit

Undefined

Note:

MSB (bit 15) is the first transmitted bit.

Whatever its size, the word must be aligned on the most significant bit (MSB)
side.

Table 7–28. Receive Data Register (RDR) – Offset address (hex): 0x00

Bit

Name

Function

Reset

Value

15–0

Received data

Undefined

Note:

LSB (bit 0) is the last received bit.

Whatever its size, the word is aligned on the least significant bit (LSB) side.

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OMAP5910

Reviews:

Related manuals for OMAP5910

Brands by name

Popular brands

Texas Instruments OMAP5910, Technical Reference Manual

Search results

Summary of Contents for OMAP5910

Reviews:

Related manuals for OMAP5910

Brands by name

Popular brands