manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

OMAP5910 Configuration Registers

6-61

MPU Private Peripherals

Table 6–46. Gate and Inhibit Control 0 Register (GATE_INH_CTRL_0) (Continued)

Bit

Reset

Value

R/W

Description

Value

Name

2

CONF_
SOFTWARE_PWR_R

This bit controls software gating and
inhibiting of the OMAP5910 I/O, which
are gated or inhibited by COM_PWR
status.

If the gating and inhibiting logic are
enabled by FUNC_MUX_CTRL_0
(10 – 13) bits and
conf_software_gate_ena_r is set to 1,
this bit controls the com_pwr gating
and inhibiting instead of device pins.

This bit has no effect in compatibility
mode.

R/W

0x0

1

CONF_
SOFTWARE_BVLZ_R

This bit controls software gating and
inhibiting of the OMAP5910 I/O, which
are gated or inhibited by
BFAIL/EXT_FIQ.

If the gating and inhibiting logic are
enabled by FUNC_MUX_CTRL_0
(10 – 13) bits and
conf_software_gate_ena_r is set to 1,
this bit controls the BFAIL/EXT_FIQ
gating and inhibiting instead of device
pins.

This bit has no effect in compatibility
mode.

R/W

0x0

0

CONF_
SOFTWARE_
GATE_ENA_R

This bit controls software gating of the
OMAP5910 I/O, which are gated or
inhibited.

If the gating and inhibiting logic are
enabled by FUNC_MUX_CTRL_0
(10 – 13) bits, this enables software to
control the gating and inhibiting instead
of device pins.

This bit has no effect in compatibility
mode.

R/W

0x0

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

Lantronix SISPM1040-582-LRT Quick Start Manual preview
SISPM1040-582-LRT
Brand: Lantronix Pages: 2
Lantronix SDS1101 Quick Start Manual preview
SDS1101
Brand: Lantronix Pages: 7
Raidon SAFETank Series User Manual preview
SAFETank Series
Brand: Raidon Pages: 49
Alcad ZA-431 Quick Start Manual preview
ZA-431
Brand: Alcad Pages: 6
IOtech ADAC/5500MF Installation Manual preview
ADAC/5500MF
Brand: IOtech Pages: 16
Avaya PARTNER PC CARD Installation Instructions preview
PARTNER PC CARD
Brand: Avaya Pages: 4
Lanner NCA-1525 User Manual preview
NCA-1525
Brand: Lanner Pages: 78
Z3 Technology SBE264-10-RPS User Instructions preview
SBE264-10-RPS
Brand: Z3 Technology Pages: 87
Lanner NCA-1040 User Manual preview
NCA-1040
Brand: Lanner Pages: 59
Cisco MERAKI MX450 Installation Manual preview
MX450
Brand: Cisco MERAKI Pages: 4
C&T Solution VCO-6131E-4M2 User Manual preview
VCO-6131E-4M2
Brand: C&T Solution Pages: 129
Gearlinx NR4400 Series User'S Quick Start Manual preview
NR4400 Series
Brand: Gearlinx Pages: 23
IBM Power System S914 Installing Instructions preview
Power System S914
Brand: IBM Pages: 48
SilverStone argon series User Manual preview
argon series
Brand: SilverStone Pages: 16
ZALMAN CNPS9700 LED User Manual preview
CNPS9700 LED
Brand: ZALMAN Pages: 8
G&D ControlCenter-IP 2.0 Installation Manual preview
ControlCenter-IP 2.0
Brand: G&D Pages: 60
Airaya AI108-1-050 Quick Install Manual preview
AI108-1-050
Brand: Airaya Pages: 28
The t.racks ACHAT DSP24 User Manual preview
ACHAT DSP24
Brand: The t.racks Pages: 24

Brands by name

Popular brands

Load more brands