manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

EMIF

 

3-36

3.7

EMIF

The external memory interface (EMIF) is a DSP subsystem module that gives
the DSP access to the shared system memory managed by the traffic control-
ler. The EMIF interfaces directly to a 32-bit wide system bus. This bus can
operate at the CPU clock rate with sustained throughput during burst
accesses. The EMIF has two control registers for user configuration:

-

EMIF global control register (GCR)

-

EMIF global reset register (GRR)

3.7.1

EMIF Global Control Register (EMIF_GCR)

The EMIF global control register (GCR) configures general operation of the
EMIF module. The EMIF GCR appears at word address 0x0800 in the DSP
I/O space.

Table 3–11.

EMIF Global Control Register (EMIF GCR)

Bit

Name

Function

Type

Reset

Value

15–12

Reserved

R

0

11–8

Reserved

RW

0

7

WPE

Write posting enable

WPE=0, write posting is disabled (for debug).
WPE=1, write posting is enabled.

RW

0

6

Reserved

RW

0

5

Reserved

RW

1

4

Reserved

R

0

3

Reserved

R

x

2

Reserved

R

x

1

Reserved

R

0

0

Reserved

RW

0

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

ZALMAN CNPS17X User Manual preview
CNPS17X
Brand: ZALMAN Pages: 20
Paradyne Hotwire 5446 Notice preview
Hotwire 5446
Brand: Paradyne Pages: 2
IEI Technology HPE-4S1 Quick Installation Manual preview
HPE-4S1
Brand: IEI Technology Pages: 3
Analog Devices Linear SCP-LT8362-S-EVALZ Demo Manual preview
Linear SCP-LT8362-S-EVALZ
Brand: Analog Devices Pages: 8
Cypress Semiconductor CY7C1019D Specification Sheet preview
CY7C1019D
Brand: Cypress Semiconductor Pages: 11
A2B Electronics ECX-200 Installation Manual preview
ECX-200
Brand: A2B Electronics Pages: 24
ZALMAN CNPS6000-Al User Manual preview
CNPS6000-Al
Brand: ZALMAN Pages: 6
Enterasys Enterasys Matrix 2G4082-25 Hardware Installation Manual preview
Enterasys Matrix 2G4082-25
Brand: Enterasys Pages: 58
Arbor Technology Em104P-i2904 Quick Installation Manual preview
Em104P-i2904
Brand: Arbor Technology Pages: 8
VCS VIP 1000 User Manual preview
VIP 1000
Brand: VCS Pages: 118
Observint NVR16 Firmware User Manual preview
NVR16
Brand: Observint Pages: 117
Boss Vocal Performer VE-20 Owner'S Manual preview
Vocal Performer VE-20
Brand: Boss Pages: 20
ZALMAN CNPS 4X User Manual preview
CNPS 4X
Brand: ZALMAN Pages: 16
AC Infinity AIRCOM Series User Manual preview
AIRCOM Series
Brand: AC Infinity Pages: 24
Intel CORE 2 DUO E4000 - 3-2008 Datasheet preview
CORE 2 DUO E4000 - 3-2008
Brand: Intel Pages: 122
A.E.B. ARCHIMEDE Fitting Instructions And Warranty Workbook preview
ARCHIMEDE
Brand: A.E.B. Pages: 28
Mitsubishi M16C/20 Series Software Manual preview
M16C/20 Series
Brand: Mitsubishi Pages: 188
ekwb EK-TIM Indigo Extreme Installation Manual preview
EK-TIM Indigo Extreme
Brand: ekwb Pages: 4

Brands by name

Popular brands

Load more brands