Texas Instruments OMAP5910 Technical Reference Manual Download Page 288 | Manualshive

Page: 288 / 1209

background image

Registers

5-55

System DMA Controller

Table 5–25. DMA LCD Control Register (DMA_LCD_CTRL) (Continued)

Bit

Reset

Value

Type

Description

Value

Name

0

FRAME_MODE

Kind of frame mode used for LCD transfer

RW

0

0

One frame buffer; only registers for frame 1 are used.

1

Two frame buffers; LCD channel reads alternatively
top_frame_1 and top_frame_2

5.6.1.1

LCD Top Address for Frame Buffer 1 Registers (DMA_LCD_TOP_F1_L and
DMA_LCD_TOP_F1_U)

The LCD top address registers are two 16-bit registers that contain the start
address for the video RAM buffer 1. The 32-bit address is obtained by the
concatenation of the two 16-bit words as described here:
LCD_TOP_F1 = DMA_LCD_TOP_F1_U & DMA_LCD_TOP_F1_L.

Note:

LSB of the 32-bit word is equal to zero. Address of video buffer must always
be even.

Table 5–26. LCD Top Address for Frame Buffer 1—Lower Bits Register

(DMA_LCD_TOP_F1_L)

Bit

Name

Description

Type

Reset

Value

15–1

LCD_TOP_F1_
L[15–1]

LCD top address for frame buffer 1 lower bits [15–1]

RW

Unde-

fined

0

LCD_TOP_F1_
L[0]

Address bit 0. Fixed at 0 since address must be even.

R

0

Table 5–27. LCD Top Address for Frame Buffer 1—Upper Bits Register

(DMA_LCD_TOP_F1_U)

Bit

Name

Description

Type

Reset

Value

15–0

LCD_TOP_F1_
L[31–16]

LCD top address for frame buffer 1 upper bits [31–16]

RW

Unde-
fined

«
...
286
287
288
289
290
...
»

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 5

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 21

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 2

WJMPU955 - PROCESSING UNIT - TMU

Brand: Panasonic Pages: 62

IntelliJack NJ200

Brand: 3Com Pages: 4

Brand: SIIG Pages: 12

Brand: FOR-A Pages: 39

Brand: Sangoma Pages: 6

Brand: PMD Pages: 74

Brand: QTech Pages: 406

Brand: ACTi Pages: 14

STEVAL-SCR002V1

Brand: ST Pages: 28

Threat Analysis Reporter TAR

Brand: 8e6 Technologies Pages: 76

X-NUCLEO-AMICAM1

Brand: ST Pages: 18

Brand: ADTRAN Pages: 4

Brand: Z3 Technology Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands