manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

MPU Memory Management Unit

2-31

MPU Subsystem

2.7.6.2

Level 1 Fetch

Bits 31–14 of the TTB register are concatenated with bits 31–20 of the virtual
address to produce a 30-bit address (see Figure 2–12) by accessing the
translation table level 1 descriptors (see Section 2.7.6.3). This address selects
a four-byte translation table entry, which is a level 1 descriptor for either a
section or a page table.

Figure 2–12. Accessing the Translation Table Level 1 Descriptors

31

20 19

18

12

14 13

2 1

0

0

0

Virtual Address

Table index

Section index

Translation base

Translation table base

First-level descriptor

Table index

Translation base

31

31

31

0

0

0

14 13

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

Salus PL07 Instruction Manual preview
PL07
Brand: Salus Pages: 16
IBM 3101 Maintenance Information preview
3101
Brand: IBM Pages: 63
IEI Technology HPE-4S1 Quick Installation Manual preview
HPE-4S1
Brand: IEI Technology Pages: 3
Alcad ZA-431 Quick Start Manual preview
ZA-431
Brand: Alcad Pages: 6
Softing CAN-PRO1-PCIE Hardware User Manual preview
CAN-PRO1-PCIE
Brand: Softing Pages: 4
Sangoma A200 Analog Installation Manual preview
A200 Analog
Brand: Sangoma Pages: 6
PMD DK55110 Manual preview
DK55110
Brand: PMD Pages: 74
AMD Geode LE-366 User Manual preview
Geode LE-366
Brand: AMD Pages: 45
Omega OMB-DAQBOARD-500 Series User Manual preview
OMB-DAQBOARD-500 Series
Brand: Omega Pages: 48
ORiNG PCard-E 021L-D5 Series Quick Installation Manual preview
PCard-E 021L-D5 Series
Brand: ORiNG Pages: 2
Nvidia GEFORCE RTX 4090 Quick Start Manual preview
GEFORCE RTX 4090
Brand: Nvidia Pages: 160
ADS Technologies API-800 Installation Manual preview
API-800
Brand: ADS Technologies Pages: 21
Zonet ZEN3320E Quick Installation Manual preview
ZEN3320E
Brand: Zonet Pages: 1
NEC N8154-25 User Manual preview
N8154-25
Brand: NEC Pages: 47
Renesas H8S/2615 Series User Manual preview
H8S/2615 Series
Brand: Renesas Pages: 28
EK-Quantum 3831109836897 User Manual preview
3831109836897
Brand: EK-Quantum Pages: 14
TQ STKa64xxL Quick Start Manual preview
STKa64xxL
Brand: TQ Pages: 2
Multitech FaxFinder FF-120 Administrator User Manual preview
FaxFinder FF-120
Brand: Multitech Pages: 20

Brands by name

Popular brands

Load more brands