manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

USB Host Controller Registers

 

14-8

14.3 USB Host Controller Registers

Most of the OMAP5910 host controller (HC) registers are the OHCI operation-
al registers, which are defined by the OHCI Specification for USB. Four
additional registers not specified by the OHCI Specification for USB provide
additional information about the USB host controller state. USB host controller
registers can be accessed in user and supervisor modes.

Note:

The USB host controller registers must be accessed using 32-bit data opera-
tions. Use of smaller data access sizes may result in unexpected operation
of the USB host controller. The USB host controller registers and the USB
host controller data structures are organized for little endian operation mode
because the TI925T MPU processor on the OMAP5910 device must use
little endian mode.

The OMAP5910 USB host controller registers are listed in Table 14–1.
Table 14–2 through Table 14–29 describe specific register bits.

Table 14–1. USB Host Controller Registers  

Name

Description

R/W

Size

†

Address

HcRevision

OHCI revision number

R

32

FFFB:A000h

HcControl

HC operating mode

R/W

32

FFFB:A004h

HcCommandStatus

HC command and status

R/W

32

FFFB:A008h

HcInterruptStatus

HC interrupt status

R/W

32

FFFB:A00Ch

HcInterruptEnable

HC interrupt enable

R/W

32

FFFB:A010h

HcInterruptDisable

HC interrupt disable

R

32

FFFB:A014h

HcHCCA

Local bus virtual address of HCCA

‡

R/W

32

FFFB:A018h

HcPeriodCurrentED

Local bus virtual address of current
periodic endpoint descriptor

‡

R/W

32

FFFB:A01Ch

HcControlHeadED

Local bus virtual address of head of
control endpoint descriptor list

‡

R/W

32

FFFB:A020h

HcControlCurrentED

Local bus virtual address of current
control endpoint descriptor

‡

R/W

32

FFFB:A024h

† Access to these registers must be by 32-bit reads or 32-bit writes. Use of other access sizes may result in undefined operation.
‡ Restrictions apply to the local bus virtual addresses used in these registers. See Section 14.6.1, Local Bus Addressing.
§ This register provides control and status for the OMAP5910 pins associated with the USB transceiver for some HMC_MODE

values.

¶ This register provides control and status for the OMAP5910 pins associated with USB port 1 for some HMC_MODE values.
# This register provides control and status for the OMAP5910 pins associated with USB port 2 for some HMC_MODE values.

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

LaCie 5big Network 2 Datasheet preview
5big Network 2
Brand: LaCie Pages: 4
LaCie d2 Network 2 Datasheet preview
d2 Network 2
Brand: LaCie Pages: 4
Compaq Proliant 800 Setup And Installation Manual preview
Proliant 800
Brand: Compaq Pages: 112
Cypress Semiconductor CY7C1329H Specification Sheet preview
CY7C1329H
Brand: Cypress Semiconductor Pages: 16
SSV Embedded Systems eSOM/3517 Hardware Reference Manual preview
eSOM/3517
Brand: SSV Embedded Systems Pages: 17
Omega OMB-DAQBOARD-500 Series User Manual preview
OMB-DAQBOARD-500 Series
Brand: Omega Pages: 48
Xtreme SNMP-2PV2 User & Installation Manual preview
SNMP-2PV2
Brand: Xtreme Pages: 83
Watchguard Firebox T20 Hardware Manual preview
Firebox T20
Brand: Watchguard Pages: 21
Idis DR-8364F Quick Manual preview
DR-8364F
Brand: Idis Pages: 16
Beckhoff EK1122 Documentation preview
EK1122
Brand: Beckhoff Pages: 84
Vivotek ND8212W Hardware Installation Manual preview
ND8212W
Brand: Vivotek Pages: 46
Commax CVN-0430F User Manual preview
CVN-0430F
Brand: Commax Pages: 122
Transition Networks PCM16-FX-LC-01 User Manual preview
PCM16-FX-LC-01
Brand: Transition Networks Pages: 5
Idex KNIGHT MT-300 Instruction Manual preview
KNIGHT MT-300
Brand: Idex Pages: 4
National Instruments GPIB-ENET-1000 Installation Manual preview
GPIB-ENET-1000
Brand: National Instruments Pages: 35
Fujitsu 467 Manual preview
467
Brand: Fujitsu Pages: 36
Extron electronics XMP 240 C AT User Manual preview
XMP 240 C AT
Brand: Extron electronics Pages: 139
Dahua H Series Quick Start Manual preview
H Series
Brand: Dahua Pages: 20

Brands by name

Popular brands

Load more brands