manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

OMAP5910 Configuration Registers

6-55

MPU Private Peripherals

Table 6–44. Pulldown Control 2 Register (PULL_DWN_CTRL_2) (Continued)

Bit

Reset

Value

R/W

Description (See Note)

Value

Name

23

CONF_PDEN_GPIO_9_R

This bit controls the pulldown enable on the
OMAP5910 I/O, which defaults to GPIO.9 at
reset.

R/W

0x0

0

Pulldown enabled

1

Pulldown disabled

The control for this pulldown is forced on at
reset and while in compatibility mode.

22

CONF_PDEN_COM_
MCLK_REQ_R

This bit controls the pulldown enable on the
OMAP5910 I/O, which defaults to
UART2.CLKREQ at reset.

R/W

0x0

0

Pulldown enabled

1

Pulldown disabled

The control for this pulldown is forced on at
reset and while in compatibility mode.

21

RESERVED

Reserved for future expansion. These bits
must always be written as 0.

R/W

0x0

20

CONF_PDEN_MCSI2_
SYNC_R

This bit controls the pulldown enable on the
OMAP5910 I/O, which defaults to
MCSI2.SYNC at reset.

R/W

0x0

0

Pulldown enabled

1

Pulldown disabled

19

RESERVED

Reserved for future expansion. These bits
must always be written as 0.

R/W

0x0

18

CONF_PDEN_MCSI2_
DIN_R

This bit controls the pulldown enable on the
OMAP5910 I/O, which defaults to
MCSI2.DIN at reset.

R/W

0x0

0

Pulldown enabled

1

Pulldown disabled

Note:

Unless otherwise indicated, pulldown control for each I/O is forced off at reset while in compatibility mode. The pull-
down control register bits only control the pulldowns while in native mode. Depending upon the pin multiplexing config-
uration of any particular I/O, a pulldown may not be available. Consult Appendix A of this document or the OMAP5910
data manual (literature number SPRS197) to determine whether a pulldown exists for each I/O.

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

XDS 910 Reference Manual preview
910
Brand: XDS Pages: 99
Idis DR-4100P Series Installation Manual preview
DR-4100P Series
Brand: Idis Pages: 30
National Instruments USB-6501 Quick Start preview
USB-6501
Brand: National Instruments Pages: 5
National Instruments PXIe-8106 User Manual preview
PXIe-8106
Brand: National Instruments Pages: 76
Ublox NEO-D9S Quick Start Manual preview
NEO-D9S
Brand: Ublox Pages: 17
Quectel Wi-Fi-M.2 EVB User Manual preview
Wi-Fi-M.2 EVB
Brand: Quectel Pages: 23
Bridgeworks a204 Hardware Manual preview
a204
Brand: Bridgeworks Pages: 18
Ensemble Designs Avenue Express Control Panel Data Pack preview
Avenue Express Control Panel
Brand: Ensemble Designs Pages: 19
Renesas RL78/G11 User Manual preview
RL78/G11
Brand: Renesas Pages: 2
ZALMAN ZM-MFC1 Combo User Manual preview
ZM-MFC1 Combo
Brand: ZALMAN Pages: 7
AOpen VA1000 Lite2 User Manual And Technical Manual preview
VA1000 Lite2
Brand: AOpen Pages: 18
Bitspower BPTA-CPUMS-V2-SKA Instruction Manual preview
BPTA-CPUMS-V2-SKA
Brand: Bitspower Pages: 6
Dahua NVRPRO User Manual preview
NVRPRO
Brand: Dahua Pages: 113
Acromag APCe7012E-LF User Manual preview
APCe7012E-LF
Brand: Acromag Pages: 23
Top RAMS1000 User Manual preview
RAMS1000
Brand: Top Pages: 21
Omron G7Z Manual preview
G7Z
Brand: Omron Pages: 11
IBA ibaPADU-S-IT-16 Manual preview
ibaPADU-S-IT-16
Brand: IBA Pages: 80
Imagine communications Selenio SNP-GW-3GX32 User Manual preview
Selenio SNP-GW-3GX32
Brand: Imagine communications Pages: 153

Brands by name

Popular brands

Load more brands