manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

McBSP3

 

9-18

9.4.4.3

Receive Control Register Configuration

The values of RWDLEN1, 2 and XWDLEN1, 2 must be set to the same value
in SPI mode.

DSP_Write(0x0000) => RCR1; set up RCR1 per below configuration.

Table 9–17. Receive Control Register 1 Configuration (DSP_Write(0x0000) => RCR1)

Bit

Config Value

Description

15

0b

Reserved

14–8

000 0000b

Set receive frame length as one word per frame

7–5

000b

Set receive word length as 8 bits per frame

4–0

0 0000b

Reserved

DSP_Write(0x0000) => RCR2; set up RCR2 per below configuration.

Table 9–18. Receive Control Register 2 Configuration (DSP_Write(0x0000) => RCR2)

Bit

Config Value

Description

15

0b

Set single-phase frame

14–8

000 0000b

Don’t care for single phase frame

7–5

000b

Don’t care for single phase frame

4–3

00b

Set no companding data and transfer start with MSB first

2

0b

Set FSR not ignore after the first resets the transfer

1–0

00b

Set data delay as 0 bit

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

ABB i-bus KNX IPR/S 3.5.1 Product Manual preview
i-bus KNX IPR/S 3.5.1
Brand: ABB Pages: 44
Mackie SP260 Installation Instructions preview
SP260
Brand: Mackie Pages: 2
Mackie SP260 Product Overview preview
SP260
Brand: Mackie Pages: 5
ekwb EK-Vector Radeon RX5700 + XT Backplate Installation Manual preview
EK-Vector Radeon RX5700 + XT Backplate
Brand: ekwb Pages: 7
MiLAN E-MCC-1600 Install Manual preview
E-MCC-1600
Brand: MiLAN Pages: 1
Symantec PacketShaper PS-S200 Quick Start Manual preview
PacketShaper PS-S200
Brand: Symantec Pages: 2
ROE EVISON HD101 User Manual preview
EVISON HD101
Brand: ROE Pages: 41
Gate NanoAAB User Manual preview
NanoAAB
Brand: Gate Pages: 8
Waves MaxxBCL Manual preview
MaxxBCL
Brand: Waves Pages: 41
Velopex Extra-X Quick Start Manual preview
Extra-X
Brand: Velopex Pages: 7
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Brand: Tandberg Data Pages: 6
IBM 8677 - BladeCenter Rack-mountable - Power Supply Planning And Installation Manual preview
8677 - BladeCenter Rack-mountable - Power Supply
Brand: IBM Pages: 126
WAGO 750-459 Manual preview
750-459
Brand: WAGO Pages: 48
Danville Signal Processing dspstak 21262sx User Manual preview
dspstak 21262sx
Brand: Danville Signal Processing Pages: 35
Lutron Electronics Smart Bridge Quick Start Manual preview
Smart Bridge
Brand: Lutron Electronics Pages: 4
XtendLan XL-HCW224C User Manual preview
XL-HCW224C
Brand: XtendLan Pages: 52
EMTRUST CP75X User Manual preview
CP75X
Brand: EMTRUST Pages: 103
Network Critical SmartNA-X User Manual preview
SmartNA-X
Brand: Network Critical Pages: 200

Brands by name

Popular brands

Load more brands