manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

OMAP5910 Configuration Registers

 

6-54

Table 6–44. Pulldown Control 2 Register (PULL_DWN_CTRL_2) (Continued)

Bit

Reset

Value

R/W

Description (See Note)

Value

Name

27

CONF_PDEN_MCBSP2_
XSYNC_R

This bit controls the pulldown enable on the
OMAP5910 I/O, which defaults to
MCBSP2.FSX at reset.

R/W

0x0

0

Pulldown enabled

1

Pulldown disabled

The control for this pulldown is forced on at
reset and while in compatibility mode.

26

CONF_PDEN_MCBSP2_
DIN_R

This bit controls the pulldown enable on the
OMAP5910 I/O, which defaults to
MCBSP2.DR at reset.

R/W

0x0

0

Pulldown enabled

1

Pulldown disabled

25

CONF_PDEN_
ARMIO_3_R

This bit controls the pulldown enable on the
OMAP5910 I/O, which defaults to MPUIO3 at
reset.

R/W

0x0

0

Pulldown enabled

1

Pulldown disabled

The control for this pulldown is forced on at
reset and while in compatibility mode.

24

CONF_PDEN_GPIO_8_R

This bit controls the pulldown enable on the
OMAP5910 I/O, which defaults to GPIO.8 at
reset.

R/W

0x0

0

Pulldown enabled

1

Pulldown disabled

The control for this pulldown is forced on at
reset and while in compatibility mode.

Note:

Unless otherwise indicated, pulldown control for each I/O is forced off at reset while in compatibility mode. The pull-
down control register bits only control the pulldowns while in native mode. Depending upon the pin multiplexing config-
uration of any particular I/O, a pulldown may not be available. Consult Appendix A of this document or the OMAP5910
data manual (literature number SPRS197) to determine whether a pulldown exists for each I/O.

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

GE 90-30 PLC User Manual preview
90-30 PLC
Brand: GE Pages: 93
CAME Z Series Manual preview
Z Series
Brand: CAME Pages: 4
Jetter JXM-IO-E30 Installation Manual preview
JXM-IO-E30
Brand: Jetter Pages: 35
PaloAlto Networks PA-7500 Quick Start Manual preview
PA-7500
Brand: PaloAlto Networks Pages: 3
Accusys ACS-76500 Owner'S Manual preview
ACS-76500
Brand: Accusys Pages: 34
AXIOMTEK tBOX330-870-FL Series Quick Installation Manual preview
tBOX330-870-FL Series
Brand: AXIOMTEK Pages: 2
Funkwerk TR 200 aw/ bw Operating Instructions preview
TR 200 aw/ bw
Brand: Funkwerk Pages: 2
EK-Quantum Kinetic FLT 80 D5/DDC Body User Manual preview
Kinetic FLT 80 D5/DDC Body
Brand: EK-Quantum Pages: 16
Dazzle Hollywood DV-Bridge User Manual preview
Hollywood DV-Bridge
Brand: Dazzle Pages: 63
protech ProX-1695 User Manual preview
ProX-1695
Brand: protech Pages: 95
MC PCIe-DIO96H User Manual preview
PCIe-DIO96H
Brand: MC Pages: 21
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Brand: ADTRAN Pages: 2
Intel BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX Product Manual preview
BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX
Brand: Intel Pages: 86
XJTAG XJLink2-CFM User Manual preview
XJLink2-CFM
Brand: XJTAG Pages: 9
Xilinx Zynq-7000 Manual preview
Zynq-7000
Brand: Xilinx Pages: 8
Freescale Semiconductor MPC8349EA MDS Getting Started Manual preview
MPC8349EA MDS
Brand: Freescale Semiconductor Pages: 8
Swann NVRx-7300 series Quick Start Manual preview
NVRx-7300 series
Brand: Swann Pages: 9
B&B Electronics PCMCIA High Speed Serial Card CE 232HSPCC User Manual preview
PCMCIA High Speed Serial Card CE 232HSPCC
Brand: B&B Electronics Pages: 14

Brands by name

Popular brands

Load more brands