manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

OMAP5910 Configuration Registers

6-43

MPU Private Peripherals

Table 6–40. Functional Multiplexing Control C Register (FUNC_MUX_CTRL_C) (Continued)

Bits

Reset

Value

R/W

Description

Name

20–18

CONF_RX2_R

These bits control the multiplexing on the
OMAP5910 I/O, which defaults to UART2.RX at
reset.

The control for this I/O is forced to 000 at reset and
while in compatibility mode.

R/W

0x0

17–15

CONF_MCBSP2_DOUT_R

These bits control the multiplexing on the
OMAP5910 I/O, which defaults to MCBSP2.DOUT
at reset.

The control for this I/O is forced to 000 at reset and
while in compatibility mode.

R/W

0x0

14–12

CONF_MCBSP2_RSYNC_R

These bits control the multiplexing on the
OMAP5910 I/O, which defaults to MCBSP2.FSR at
reset.

The control for this I/O is forced to 000 at reset and
while in compatibility mode.

R/W

0x0

11–9

RESERVED

Reserved for future expansion. These bits must
always be written as 0.

R/W

0x0

8–6

CONF_MCBSP2_CLKR_R

These bits control the multiplexing on the
OMAP5910 I/O, which defaults to MCBSP2.CLKR
at reset.

The control for this I/O is forced to 000 at reset and
while in compatibility mode.

R/W

0x0

5–3

RESERVED

Reserved for future expansion. These bits must
always be written as 0.

R/W

0x0

2–0

CONF_MCBSP2_DIN_R

These bits control the multiplexing on the
OMAP5910 I/O, which defaults to MCBSP2.DR at
reset.

The control for this I/O is forced to 000 at reset and
while in compatibility mode.

R/W

0x0

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

FabiaTech FX5638 Series Users Quick Reference preview
FX5638 Series
Brand: FabiaTech Pages: 4
Harmonic XOS User Manual preview
XOS
Brand: Harmonic Pages: 56
Commell ES-270 User Manual preview
ES-270
Brand: Commell Pages: 36
TFortis Teleport-1 Configuration Manual preview
Teleport-1
Brand: TFortis Pages: 86
Cypress Semiconductor CY7C1019D Specification Sheet preview
CY7C1019D
Brand: Cypress Semiconductor Pages: 11
Zoom 4412A User Manual preview
4412A
Brand: Zoom Pages: 48
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
Dantel 46020-38 Installation & Operation Manual preview
46020-38
Brand: Dantel Pages: 62
Nakayo NYC-16VDSL-B Instruction & Installation Manual preview
NYC-16VDSL-B
Brand: Nakayo Pages: 119
Nvidia GEFORCE RTX 4090 Quick Start Manual preview
GEFORCE RTX 4090
Brand: Nvidia Pages: 160
Aaeon GENE-EHL7 User Manual preview
GENE-EHL7
Brand: Aaeon Pages: 119
McIntosh MX160 Owner'S Manual preview
MX160
Brand: McIntosh Pages: 44
Renesas M32173T-PTC User Manual preview
M32173T-PTC
Brand: Renesas Pages: 7
ASTRO U 960 Operating Manual preview
U 960
Brand: ASTRO Pages: 12
b&t RTL8720D Instruction Manual preview
RTL8720D
Brand: b&t Pages: 34
Curtiss-Wright KAD/UBM/105 Quick Start Manual preview
KAD/UBM/105
Brand: Curtiss-Wright Pages: 12
Curtiss-Wright GT200 VME Hardware Reference Manual preview
GT200 VME
Brand: Curtiss-Wright Pages: 58
MSI TV Series User Manual preview
TV Series
Brand: MSI Pages: 90

Brands by name

Popular brands

Load more brands