manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

Register Map

 

13-32

13.2.12.1

Transmit DMA CH.n Done Interrupt Flag (TXn_Done)

Only for non-isochronous DMA transfer. This bit is never set for isochronous
DMA transfer.

This bit is set automatically by the core when a transmit DMA channel has com-
pleted the programmed transfer by servicing the last IN transaction from the
USB host. This is when TXn_TSC (transfer size counter) equals 0 and the last
IN transaction completes with an ACK. When this bit is asserted, the local host
must read the DMAN_STAT register to identify the endpoint number for which
the transfer completed.

The endpoint interrupt the EPn_TX is never set for the assigned endpoint to
TX DMA channel n.

0: No action

1: Non-isochronous transmit DMA transfer for a channel has ended.

Value after local host or USB reset is low.

13.2.12.2

RX DMA CH.n Transactions Count Interrupt Flag (RXn_Cnt)

Only for non-isochronous DMA transfer. This bit is never set for isochronous
DMA transfer.

This bit is set automatically by the core during an active receive DMA transfer
each time RXn_TC equals 0 after an OUT transaction with ACK status. This
bit is set after RX DMA data has been read (end of DMA request). When this
bit is asserted, the local host must read the DMAN_STAT register to identify
the endpoint number for which the transfer completed. An RXn_Cnt interrupt
is asserted also if the RXn_Stop bit is set; in this case, both the RXn_EOT and
the RXn_Cnt are asserted.

0: No action

1: Non-isochronous receive DMA transfer for a channel has reached transac-
tions count level.

Value after local host or USB reset is low.

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

D-Link xStack Storage DSN-4000 Series Datasheet preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 5
Campbell NL115 User Manual preview
NL115
Brand: Campbell Pages: 38
Hama 00039747 Operating Instruction preview
00039747
Brand: Hama Pages: 6
H3C LSWM12H2Q User Manual preview
LSWM12H2Q
Brand: H3C Pages: 9
ZALMAN CNPS5X PERFORMA User Manual preview
CNPS5X PERFORMA
Brand: ZALMAN Pages: 8
Symantec SV1800 Series Safety And Regulatory Compliance Manual preview
SV1800 Series
Brand: Symantec Pages: 100
ZiLOG Z8 GP ZGP323 User Manual preview
Z8 GP ZGP323
Brand: ZiLOG Pages: 11
Datum bc635VME Operation And Technical Manual preview
bc635VME
Brand: Datum Pages: 49
Meinberg CPU-C15G2 Setup Manual preview
CPU-C15G2
Brand: Meinberg Pages: 14
A.E.B. ARCHIMEDE Fitting Instructions And Warranty Workbook preview
ARCHIMEDE
Brand: A.E.B. Pages: 28
B&B Electronics PCMCIA 232PCC2 Owner'S Manual preview
PCMCIA 232PCC2
Brand: B&B Electronics Pages: 24
Cypress Semiconductor CY7C027AV Specification Sheet preview
CY7C027AV
Brand: Cypress Semiconductor Pages: 18
Avigilon NVR5-STD-10GBE Installation Manual preview
NVR5-STD-10GBE
Brand: Avigilon Pages: 12
Renesas RL78/L1C User Manual preview
RL78/L1C
Brand: Renesas Pages: 4
PairGain HiGain Line Unit HLU-388 Quick Installation Manual preview
HiGain Line Unit HLU-388
Brand: PairGain Pages: 7
NUROTRON CS-10A Operation Manual preview
CS-10A
Brand: NUROTRON Pages: 16
Alvarion BreezeNET DS.11 Configuration Utility Release Note preview
BreezeNET DS.11 Configuration Utility
Brand: Alvarion Pages: 2
Beck com.tom INDUSTRY 100.WLAN.W Startup Manual preview
com.tom INDUSTRY 100.WLAN.W
Brand: Beck Pages: 2

Brands by name

Popular brands

Load more brands