manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

McBSP3

 

9-14

9.4.2

McBSP3 Interrupt Mapping

Table 9–13 identifies the McBSP3 interrupts. McBSP3 generates level 2
interrupts for both the DSP and the MPU.

Table 9–13. McBSP3 Interrupt Mapping

Incoming Interrupts

Level 2 DSP Interrupt

Level 2 MPU Interrupt

McBSP3 TX interrupt

IRQ_00

IRQ_10

McBSP3 RX interrupt

IRQ_01

IRQ_11

9.4.3

McBSP3 DMA Request Mapping

Table 9–14 identifies McBSP3 DMA request lines.

Table 9–14. DMA Request Mapping—McBSP3

DMA Request Source

DMA Request Line—DSP

DMA Request Line—

MPU

McBSP3 TX

DMA_REQ_10

DMA_REQ_10

McBSP3 RX

DMA_REQ_11

DMA_REQ_11

9.4.4

McBSP3 Application Example: Optical Interface

With the assistance of two GPIOs, McBSP3 is configured to connect to an
external optical audio interface (see Figure 9–6) device such as the Sanyo
LC89051V. The CLKS signal is the active input clock for the McBSP modem
block. The active input clock can be changed in a McBSP register, but activity
on CLKS is required to perform the set up and write to the McBSP register.

Section 9.4.4.1 through Section 9.4.4.12 explain the McBSP register setup for
optical interface with 8-bit transfer per frame in SPI master mode and GPIO
mode.

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

Radwin Transportation FiberinMotion Deployment Manual preview
Transportation FiberinMotion
Brand: Radwin Pages: 122
Advantech 3718HG User Manual preview
3718HG
Brand: Advantech Pages: 68
Avocent Cyclades CS4008 Specifications preview
Cyclades CS4008
Brand: Avocent Pages: 2
SIIG SATA II-150 PCI Quick Installation Manual preview
SATA II-150 PCI
Brand: SIIG Pages: 16
XtendLan XL-VC102SB User Manual preview
XL-VC102SB
Brand: XtendLan Pages: 17
DIGITAL-LOGIC MICROSPACE MSEBX800 User Manual preview
MICROSPACE MSEBX800
Brand: DIGITAL-LOGIC Pages: 53
MESA Electronic 4C24 Manual preview
4C24
Brand: MESA Electronic Pages: 27
Eneo PNR-5332/3TB Quick Installation Manual preview
PNR-5332/3TB
Brand: Eneo Pages: 49
ekwb EK-TIM Indigo Extreme Installation Manual preview
EK-TIM Indigo Extreme
Brand: ekwb Pages: 4
Transition Networks PCM16-FX-LC-01 User Manual preview
PCM16-FX-LC-01
Brand: Transition Networks Pages: 5
B&B Electronics ZXT9-IO-222R2 Product Manual preview
ZXT9-IO-222R2
Brand: B&B Electronics Pages: 74
Icop VMXP-6453 User Manual preview
VMXP-6453
Brand: Icop Pages: 31
ABB M1M 10 Quick Start Manual preview
M1M 10
Brand: ABB Pages: 2
ABB RobotWare 6.02 Applications Manual preview
RobotWare 6.02
Brand: ABB Pages: 52
ABB M4M 30 User Manual preview
M4M 30
Brand: ABB Pages: 84
Cisco NM-1A-E3 User Manual preview
NM-1A-E3
Brand: Cisco Pages: 26
Cisco Linksys WET610N Quick Installation Manual preview
Linksys WET610N
Brand: Cisco Pages: 78
Cisco MX60 Manual preview
MX60
Brand: Cisco Pages: 8

Brands by name

Popular brands

Load more brands