manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

OMAP5910 Configuration Registers

 

6-66

Table 6–49. Module Configuration Control 0 Register (MOD_CONF_CTRL_0) (Continued)

Bit

Reset

Value

R/W

Description

Value

Name

18

CONF_MOD_MCBSP1_
AUXON

This bit enables the McBSP1 AUXON
functionality, which gates the functional
clock to the corresponding McBSP module.

R/W

0x0

0

The internal functional clock to McBSP1 is
active and depends upon the McBSP
configuration.

1

The internal functional clock to McBSP1 is
disabled or gated.

17

CONF_MOD_USB_W2FC_
VBUS_MODE_R

This bit determines what hardware method
is used for USB.VBUS detection.

R/W

0x0

0

The VBUS detection is under control of the
GPIO0 input.

1

The VBUS detection is under control of the
VBUS detection I/O cell.

This bit resets to 0 during reset and
compatibility mode.

16

CONF_MOD_I2C_
SELECT_R

This bit selects the I

2

C module

compatibility mode. This bit resets to
standard mode.

R/W

0x0

0

The I

2

C module is in standard mode.

1

The I

2

C module is in compatibility mode.

15–14 RESERVED

Reserved for future expansion. These bits
must always be written as 0.

R/W

0x0

13

CONF_MOD_SDRAM_
EMRS_BA1_CTRL

This bit allows the user to force the
SDRAM SDRAM.BA[1] pin to a high. With
proper disabling of SDRAM accesses from
OMAP5910, users can use this to program
the EMRS register of the SDRAM with an
MRS write instruction.

There are no hardware hooks to only
assert this when performing an MRS write.
Firmware must determine how to properly
control this.

R/W

0x0

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

GE MDS SD Series Setup Manual preview
MDS SD Series
Brand: GE Pages: 4
Harman Kardon CITATION 7.0 Owner'S Manual preview
CITATION 7.0
Brand: Harman Kardon Pages: 66
Paradyne 3172 Quick Reference preview
3172
Brand: Paradyne Pages: 20
Paradyne Compshere 3000 Series Notice preview
Compshere 3000 Series
Brand: Paradyne Pages: 2
D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Manual preview
AirPlus XtremeG Ethernet-to-Wireless Bridge...
Brand: D-Link Pages: 31
KEMP Technologies LoadMaster 1500 Installation And Configuration Manual preview
LoadMaster 1500
Brand: KEMP Technologies Pages: 71
Telit Wireless Solutions HE922-3GR Hardware User'S Manual preview
HE922-3GR
Brand: Telit Wireless Solutions Pages: 113
Lanner electronics EM-566 Series Manual preview
EM-566 Series
Brand: Lanner electronics Pages: 59
Aqua Computer Aquaduct 360 XT Operating And Assembly Manual preview
Aquaduct 360 XT
Brand: Aqua Computer Pages: 28
ENERMAX ELC-LTTR240-TBP User Manual preview
ELC-LTTR240-TBP
Brand: ENERMAX Pages: 16
Cypress Semiconductor CY7C1329H Specification Sheet preview
CY7C1329H
Brand: Cypress Semiconductor Pages: 16
ekwb EK-Loop Modulus Series User Manual preview
EK-Loop Modulus Series
Brand: ekwb Pages: 7
Dataprobe iBoot-Exp Manual preview
iBoot-Exp
Brand: Dataprobe Pages: 5
KonNad SinoCon C2000-C2-SHK0401-BB1 User Manual preview
SinoCon C2000-C2-SHK0401-BB1
Brand: KonNad Pages: 12
Intel RS25AB080 Tested Hardware And Operating System List preview
RS25AB080
Brand: Intel Pages: 26
Isee IGEPv2 BOARD Hardware Reference Manual preview
IGEPv2 BOARD
Brand: Isee Pages: 68
ekwb EK-FC750 GTX Series Installation Manual preview
EK-FC750 GTX Series
Brand: ekwb Pages: 2
ADTRAN 1202052L1 User Manual preview
1202052L1
Brand: ADTRAN Pages: 136

Brands by name

Popular brands

Load more brands