manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

MCSI2

 

9-54

9.7

MCSI2

This section provides information specific to MCSI2 (Figure 9–30) on the
OMAP5910 device.

9.7.1

MCSI2 Pin Description

Table 9–41 identifies the MCSI2 I/O pins.

Table 9–41. MCSI2 Pin Descriptions

Pin

I/O Direction

Description

MCSI2.DIN

In

Data input

MCSI2.DOUT

Out

Data output

MCSI2.CLK

In/out

Bit clock

MCSI2.SYNC

In/out

Frame synchronization

9.7.2

MCSI2 Interrupt Mapping

Table 9–42 identifies the MCSI2 interrupts. MCSI2 generates level 2 interrupts
for both the DSP and the MPU. Only one MPU MCSI2 interrupt covers TX, RX,
and frame error conditions; software must check the MCSI2 status register to
determine the interrupt source.

Table 9–42. MCSI2 Interrupt Mapping

Incoming Interrupts

Level 2 DSP Interrupt

Level 2 MPU Interrupt

MCSI2 TX interrupt

IRQ_08

IRQ_17

MCSI2 RX interrupt

IRQ_09

IRQ_17

MCSI2 Frame Error

IRQ_11

IRQ_17

9.7.3

MCSI2 DMA Request Mapping

Table 9–43 identifies MCSI2 DMA request lines. Only the DSP DMA controller
can transfer MCSI2 data; there is no MPU DMA capability.

Table 9–43. DMA Request Mapping—MCSI2

DMA Request Source

DMA Request Line—DSP

DMA Request Line—MPU

MCSI2 TX

DMA_REQ_03

–

MCSI2 RX

DMA_REQ_04

–

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

HMS Networks Anybus Communicator ABC4021 User Manual preview
Anybus Communicator ABC4021
Brand: HMS Networks Pages: 60
Lanner electronics EM-566 Series Manual preview
EM-566 Series
Brand: Lanner electronics Pages: 59
ICP Chapter C Quick Setup Manual preview
Chapter C
Brand: ICP Pages: 68
Nortel BayStack 660 Use Manual preview
BayStack 660
Brand: Nortel Pages: 163
Baracoda Scan Dongle User Manual preview
Scan Dongle
Brand: Baracoda Pages: 16
ICP DAS USA I-87K Series User Manual preview
I-87K Series
Brand: ICP DAS USA Pages: 31
Lattice Semiconductor LatticeMico GPIO Manual preview
LatticeMico GPIO
Brand: Lattice Semiconductor Pages: 28
8e6 Technologies HL-002-006 Quick Start Manual preview
HL-002-006
Brand: 8e6 Technologies Pages: 94
Renesas Emulation Memory Board R0E330850MSRC0 User Manual preview
Emulation Memory Board R0E330850MSRC0
Brand: Renesas Pages: 4
DPS Telecom D-PK-NG432 User Manual preview
D-PK-NG432
Brand: DPS Telecom Pages: 80
ICP GDT6618RD Addendum preview
GDT6618RD
Brand: ICP Pages: 111
Dahua Technology NVR52A16-16P-4KS2 Quick Start Manual preview
NVR52A16-16P-4KS2
Brand: Dahua Technology Pages: 13
Belkin Wireless G F5D7000 User Manual preview
Wireless G F5D7000
Brand: Belkin Pages: 252
ADTRAN NetVanta 3430 Manual preview
NetVanta 3430
Brand: ADTRAN Pages: 2
ADTRAN OC-12 Manual preview
OC-12
Brand: ADTRAN Pages: 2
ADTRAN SFP Series Quick Start preview
SFP Series
Brand: ADTRAN Pages: 4
ADTRAN TRACER 4205 Quick Start Manual preview
TRACER 4205
Brand: ADTRAN Pages: 9
AT&T AC8200 Installation Manual preview
AC8200
Brand: AT&T Pages: 16

Brands by name

Popular brands

Load more brands