manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

USB Host Controller Registers

 

14-40

Table 14–25. HC Port 3 Status and Control Register (HcRhPortStatus3) (Continued)

Bit

Reset

Value

Type

Description

Name

4

PRS/SPR

Port 3 port reset status/set port reset

When read as 1, indicates that port 3 is receiving the USB
reset signaling. When read as 0, USB reset is not being sent
to port 3.

A write of 1 to this bit sets the port 3 port reset status bit and
cause the USB host controller to begin signaling USB reset
to port 3. A write of 0 to this bit has no effect.

R/W

0

3

POCI/CSS

Port 3 port overcurrent indicator/clear suspend status

When read as 1, indicates that a port 3 port overcurrent
condition has occurred. When 0, no port 3 port overcurrent
condition has occurred.

The OMAP5910 does not provide inputs for signaling
external overcurrent indication to the USB host controller.
Overcurrent monitoring, if required, must be handled through
some other mechanism.

A write of 1 to this bit when port 3 port suspend status is 1
causes resume signaling on port 3. A write of 1 when port 3
port suspend status is 0 has no effect. A write of 0 has no
effect.

R/W

0

2

PSS/SPS

Port 3 port suspend status/set port suspend

When read as 1, indicates that port 3 is in the USB suspend
state, or is in the resume sequence. When 0, indicates that
port 3 is not in the USB suspend state. This bit is cleared
automatically at the end of the USB resume sequence and
also at the end of the USB reset sequence.

If port 3 CurrentConnectStatus is 1, a write of 1 to this bit
sets the port 3 port suspend status bit and places port 3 in
USB suspend state. If CurrentConnectState is 0, a write of 1
instead sets ConnectStatusChange to inform the USB host
controller driver software of an attempt to suspend a
disconnected device. A write of 0 to this bit has no effect.

R/W

0

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

ZALMAN CNPS17X User Manual preview
CNPS17X
Brand: ZALMAN Pages: 20
STMicroelectronics ST62GP-EMU2 HDS2 Series User Manual preview
ST62GP-EMU2 HDS2 Series
Brand: STMicroelectronics Pages: 58
M86 Security M86 Web Filter User Manual preview
M86 Web Filter
Brand: M86 Security Pages: 309
Aaeon SBC-555 Manual preview
SBC-555
Brand: Aaeon Pages: 72
Active Communications ACS express Quick Start Manual preview
ACS express
Brand: Active Communications Pages: 10
Segger J-Link-OB-STM32F072-128KB User Manual preview
J-Link-OB-STM32F072-128KB
Brand: Segger Pages: 18
Seagate CHEETAH ST34501FC Product Manual preview
CHEETAH ST34501FC
Brand: Seagate Pages: 68
SriHome NVS001B Quick Operation Manual preview
NVS001B
Brand: SriHome Pages: 12
VideoWave Adam Device User Manual preview
Adam Device
Brand: VideoWave Pages: 12
UNICORECOMM UM620N User Manual preview
UM620N
Brand: UNICORECOMM Pages: 19
IEI Technology Mustang-M2AE-MX1 User Manual preview
Mustang-M2AE-MX1
Brand: IEI Technology Pages: 58
COUGAR Vortex SPB 120 User Manual preview
Vortex SPB 120
Brand: COUGAR Pages: 2
FOR-A USF-105PS Operation Manuals preview
USF-105PS
Brand: FOR-A Pages: 37
Wistron NeWeb DNBA-81 User Manual preview
DNBA-81
Brand: Wistron NeWeb Pages: 32
Cooler Master MCY-C3P1-KWNN Manual preview
MCY-C3P1-KWNN
Brand: Cooler Master Pages: 4
Allied Telesis AT-TN109-A Specifications preview
AT-TN109-A
Brand: Allied Telesis Pages: 2
Xaoc Devices NIN Operator'S Manual preview
NIN
Brand: Xaoc Devices Pages: 4
Altera tPad DE2-115 User Manual preview
tPad DE2-115
Brand: Altera Pages: 43

Brands by name

Popular brands

Load more brands