manualshive.com logo in svg

Texas Instruments OMAP5910, Technical Reference Manual

The Texas Instruments OMAP5910 is an advanced electronic device, offering exceptional functionalities and high performance. To make the most out of this product, it is advisable to refer to the comprehensive "Reference Manual" available for download, free of charge, from our website.

Share
Download
background image

Pseudonoise Pulse-Width Light Modulator

7-51

MPU Public Peripherals

7.6.2

PWL Registers

The PWL is connected to the host with a TIPB. The PWL control is done with
two 8-bit registers. All TIPB accesses are done asynchronously with the
32-kHz clock, meaning there is no TIPB wait-state insertion.

Table 7–41 lists the PWL registers. Table 7–42 and Table 7–43 describe the
individual registers.

Start address (hex): FFFB:5800

Table 7–41. PWL Registers

Name

Description

R/W

Size

Address

Offset

PWL_LEVEL

PWL-level

R/W

8 bits

FFFB:5800

0x00

PWL_CTRL

PWL control

R/W

8 bits

FFFB:5800

0x04

Table 7–42. PWL Level Register (PWL_LEVEL)

Offset address (hex): 0x00

Bit

Name

Function

Reset

Value

7–0

PWL_LEVEL

Defines the mean value of the PWL output signal. 0
leads to a continuous 0 output. 255 to an almost
continuous 1 output: 255/256 cycles in high level.

0

Table 7–43. PWL Control Register (PWL_CTRL)

Offset address (hex): 0x04

Bit

Name

Function

Reset

Value

7–1

–

Reserved

0

CLK_ENABLE

Internal clock is enabled when 1.

0

Summary of Contents for OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP5910

Magma PE6R4-I Quick Installation Manual preview
PE6R4-I
Brand: Magma Pages: 2
SAF Phoenix G2 IDU Quick Start Manual preview
Phoenix G2 IDU
Brand: SAF Pages: 30
Quantum LightSpeed Appliance QLS250 Owner'S Manual preview
LightSpeed Appliance QLS250
Brand: Quantum Pages: 12
QNAP TS-1283XU-RP User Manual preview
TS-1283XU-RP
Brand: QNAP Pages: 54
Teletronics International TT 900 User Manual preview
TT 900
Brand: Teletronics International Pages: 57
Omega OMB-DAQBOARD-500 Series User Manual preview
OMB-DAQBOARD-500 Series
Brand: Omega Pages: 48
Ubiquiti UniFi WiFi BaseStation XG Quick Start Manual preview
UniFi WiFi BaseStation XG
Brand: Ubiquiti Pages: 19
CG Emotron OSTO 100 Instruction Manual preview
Emotron OSTO 100
Brand: CG Pages: 112
Cypress Semiconductor CY8C24223A Specification Sheet preview
CY8C24223A
Brand: Cypress Semiconductor Pages: 31
NEC N8154-25 User Manual preview
N8154-25
Brand: NEC Pages: 47
Renesas H8S/2615 Series User Manual preview
H8S/2615 Series
Brand: Renesas Pages: 28
ADC 150-204-100-03 User Manual preview
150-204-100-03
Brand: ADC Pages: 29
Acces I/O products mPCIE-ADIO16-8F Series Hardware Manual preview
mPCIE-ADIO16-8F Series
Brand: Acces I/O products Pages: 13
M86 Security IR Web Filter User Manual preview
IR Web Filter
Brand: M86 Security Pages: 540
Proxim Lynx.GX 16T Installation And Management Manual preview
Lynx.GX 16T
Brand: Proxim Pages: 45
Canon Wireless LAN Board-B2 User Manual preview
Wireless LAN Board-B2
Brand: Canon Pages: 100
D-Link Nuclias DNH-100 Quick Installation Manual preview
Nuclias DNH-100
Brand: D-Link Pages: 16
D-Link DSS-8+ User Manual preview
DSS-8+
Brand: D-Link Pages: 26

Brands by name

Popular brands

Load more brands