manualshive.com logo in svg

Freescale Semiconductor MC9S12ZVHL32, Reference Manual

The Freescale Semiconductor MC9S12ZVHL32 is a powerful microcontroller designed for automotive applications. For a comprehensive understanding of its features and functionalities, make sure to download the free Reference Manual from manualshive.com. This manual provides detailed instructions for maximizing the performance of this cutting-edge product.

Share
Download
background image

Chapter 10 Analog-to-Digital Converter (ADC12B_LBA_V1) 

S12ZVHY/S12ZVHL Family Reference Manual Rev. 1.05

358

Freescale Semiconductor

NOTE

In principle, the MCU could stay in Wait Mode for a shorter period of time 
than the ADC needs to abort an ongoing conversion (range of µµµµ

s). 

Therefore in case a Sequence Abort Event is issued automatically due to 
MCU Wait Mode request a following Restart Event after exit from MCU 
Wait Mode can not be executed before ADC has finished this Sequence 
Abort Event. The Restart Event is detected but it is pending. 
This applies in case MCU Wait Mode is exited before ADC has finished the 
Sequence Abort Event and a Restart Event is issued immediately after exit 
from MCU Wait Mode. Bit READY can be used by software to detect when 
the Restart Event can be issued without latency time in processing the event 
(see also 

Figure 10-1

).

Figure 10-1. Conversion Flow Control Diagram - Wait Mode (SWAI=1’b1, AUT_RSTA=1’b0)

•

MCU Freeze Mode

Depending on the ADC Freeze Mode configuration bit FRZ_MOD, the ADC either continues 
conversion in Freeze Mode or freezes conversion at next conversion boundary before the MCU 
Freeze Mode is entered. After exit from MCU Freeze Mode with previously frozen conversion 
sequence the ADC continues the conversion with the next conversion command and all ADC 
interrupt flags are unchanged during MCU Freeze Mode.

CSL_0

Active 

AN3 AN1 AN4 IN5 AN6 AN1

Wait Mode request (SWAI=1’b1),

Automatic Sequence Abort

Event

Wait Mode

entry

Wake-up

Event 

Idle

Active 

AN3 AN1 AN4

Abort

Sequence_n

EOS

Sequence_0

AN5 AN2 AN0

Sequence_1

Trigger

Begin from top of current CSL

READY=1’b1

Restart 

Event

Earliest point of time to issue

Restart Event without latency

t

Summary of Contents for MC9S12ZVHL32











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MC9S12ZVHL32

Falcon RS500 Owner'S And Installer'S Manual preview
RS500
Brand: Falcon Pages: 3
MADRIX AURA Technical Manual & Quick Start Manual preview
AURA
Brand: MADRIX Pages: 36
ADEMCO MAX Programming Instructions preview
MAX
Brand: ADEMCO Pages: 2
Calpeda IDROMAT 5 Quick Start Manual preview
IDROMAT 5
Brand: Calpeda Pages: 4
Airlow CP Touch User Manual preview
CP Touch
Brand: Airlow Pages: 20
Rare Waves Grendel 2TAC Manual preview
Grendel 2TAC
Brand: Rare Waves Pages: 18
Danfoss ECL Comfort 300 User Manual preview
ECL Comfort 300
Brand: Danfoss Pages: 75
Genasun GVB-8-WP Series Manual preview
GVB-8-WP Series
Brand: Genasun Pages: 8
Holars AS H-TAG User Manual preview
H-TAG
Brand: Holars AS Pages: 15
ICP DAS USA WISE-5801 Application Example preview
WISE-5801
Brand: ICP DAS USA Pages: 20
iNels JA3-018M Quick Start Manual preview
JA3-018M
Brand: iNels Pages: 2
Kontron M2M Smart Service Developer Kit Getting Started Manual preview
M2M Smart Service Developer Kit
Brand: Kontron Pages: 27
C Prox Ltd DPS-T User Manual preview
DPS-T
Brand: C Prox Ltd Pages: 9
BFT COMPASS SC-RS 232 Installation And User Manual preview
COMPASS SC-RS 232
Brand: BFT Pages: 24
W8ZR StationPro II Operating Manual preview
StationPro II
Brand: W8ZR Pages: 77
Wahlberg 255.700 User Manual preview
255.700
Brand: Wahlberg Pages: 40
Eaton Smart Home Controller 2.0 Quick Installation Manual preview
Smart Home Controller 2.0
Brand: Eaton Pages: 24
DYNACO DYNALOGIX II DY 4000 Electrical Manual preview
DYNALOGIX II DY 4000
Brand: DYNACO Pages: 13

Brands by name

Popular brands

Load more brands