manualshive.com logo in svg

Freescale Semiconductor MC9S12ZVHL32, Reference Manual

The Freescale Semiconductor MC9S12ZVHL32 is a powerful microcontroller designed for automotive applications. For a comprehensive understanding of its features and functionalities, make sure to download the free Reference Manual from manualshive.com. This manual provides detailed instructions for maximizing the performance of this cutting-edge product.

Share
Download
background image

Chapter 6 S12Z Debug (S12ZDBGV2) Module

S12ZVHY/S12ZVHL Family Reference Manual Rev. 1.05 

Freescale Semiconductor 

    

189

6.3.2.4

Debug Trace Control Register Low (DBGTCRL)

Read: Anytime.

Write: Anytime the module is disarmed and PTACT is clear.

This register configures the profiling and timestamp features

10

Detail

11

Pure PC

Table 6-11. TALIGN Trace Alignment Encoding

TALIGN

Description

00

Trigger ends data trace

01

Trigger starts data trace

10

32 lines of data trace follow trigger

11

(1)

1. Tracing/Profiling disabled. 

Reserved

Address: 0x0103

 

7

6

5

4

3

2

1

0

R

0

0

0

0

DSTAMP

PDOE

PROFILE

STAMP

W

Reset

0

0

0

0

0

0

0

0

= Unimplemented or Reserved

Figure 6-6. Debug Trace Control Register Low (DBGTCRL)

 

Table 6-12. DBGTCRL Field Descriptions

Field

Description

3

DSTAMP

Comparator D Timestamp Enable 

— This bit, when set, enables Comparator D matches to generate 

timestamps in Detail, Normal and Loop1 trace modes.
0 Comparator D match does not generate timestamp
1 Comparator D match generates timestamp if timestamp function is enabled

2

PDOE

Profile Data Out Enable 

— This bit, when set, configures the device profiling pins for profiling. 

0 Device pins not configured for profiling
1 Device pins configured for profiling

1

PROFILE

Profile Enable 

— This bit, when set, enables the profile function, whereby a subsequent arming of the DBG 

activates profiling. 
When PROFILE is set, the TRCMOD bits are ignored.
0 Profile function disabled
1 Profile function enabled

Table 6-10. TRCMOD Trace Mode Bit Encoding

TRCMOD

Description

Summary of Contents for MC9S12ZVHL32











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MC9S12ZVHL32

ABB ControlMaster CM15 Instructions preview
ControlMaster CM15
Brand: ABB Pages: 4
S&C 5800 Series Troubleshooting Manual preview
5800 Series
Brand: S&C Pages: 34
CAME Z Series Technical Documentation Manual preview
Z Series
Brand: CAME Pages: 16
Ultrak KEGS5000 User Manual preview
KEGS5000
Brand: Ultrak Pages: 41
Zander Aachen ZX Series Quick Start Manual preview
ZX Series
Brand: Zander Aachen Pages: 10
hager coviva Smartbox TKP100A Configuration Manual preview
coviva Smartbox TKP100A
Brand: hager Pages: 45
Lantronix xPico 200 Series Manual preview
xPico 200 Series
Brand: Lantronix Pages: 7
Lantronix xPico 110 Quick Start Manual preview
xPico 110
Brand: Lantronix Pages: 3
Lantronix EDS1100 Quick Start Manual preview
EDS1100
Brand: Lantronix Pages: 15
Ultratec SureFire Operation Manual preview
SureFire
Brand: Ultratec Pages: 33
XtendLan KEYBPTZ4D Operating Instructions Manual preview
KEYBPTZ4D
Brand: XtendLan Pages: 12
YASKAWA MP2600iec Hardware Manual preview
MP2600iec
Brand: YASKAWA Pages: 42
YASKAWA MP210 Series User Manual preview
MP210 Series
Brand: YASKAWA Pages: 351
Gardena 1891-20 Operator'S Manual preview
1891-20
Brand: Gardena Pages: 15
Danfoss AME 15 QM Instructions Manual preview
AME 15 QM
Brand: Danfoss Pages: 14
Harmonic Drive YukonDrive-1021 Operating Manual preview
YukonDrive-1021
Brand: Harmonic Drive Pages: 53
SAES NEG POWER User Manual preview
NEG POWER
Brand: SAES Pages: 36
Atmel ATmega161 Manual preview
ATmega161
Brand: Atmel Pages: 150

Brands by name

Popular brands

Load more brands