Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 96 / 535

2-58

22. Turn the engine upside down on support blocks and

remove the coolant temperature sensor (if neces-

sary).

FC033

23. With its bottom side up on two support blocks,

remove the cap screws securing the crankcase

halves.

24. Separate the crankcase halves by installing two

crankcase cap screws in opposite corners leaving the

heads approximately 1/4 in. out. Using a plastic ham-

mer and lifting on the ends of the crankshaft, tap on

each cap screw head until the case halves separate.

Remove the cap screws.

FC034

25. Lift the bottom half of the crankcase off the top half.

26. Lift the crankshaft free from the top half of the

crankcase and slide the crankshaft oil seals off the

crankshaft. Account for the C-ring. Remove the

bearing retaining pins and account for the crankcase

dowel pins.



NOTE: The end bearings are not pressed onto the

crankshaft. After removing the seals, use care not to
allow the bearings to slide off the crankshaft.

27. Remove the oil-injection pump/water pump drive-

shaft from the lower crankcase half. Account for the

thrust washer on the outer end of the shaft.

CM159A



NOTE: When replacing the inner water pump seals,

use the recommended Water Pump Bearing and Seal
Tool Kit only.

28. Place the crankcase on the bench with the water

pump side down. Using the long seal driver, drive the

mechanical water pump seal from the crankcase.

FC036

29. Using a pair of snap ring pliers, remove the snap ring

securing the inner seal in the crankcase.

30. Using the hooked end of the tool, pull the inner seal

free of the crankcase.

31. Using the hooked end of the tool, pry the seal ring

from the backside of the water pump impeller.

AN327D

CAUTION

DO NOT drive any tool between halves to separate the
crankcase. Damage to the sealing surfaces will result.

CAUTION

Care must be taken to not allow the connecting rods to
drop onto the sealing surface of the bottom case half.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды