Arctic Cat Sno Pro 120 2011 страница 147 Скачать руководство пользователя

Страница: 147 / 535

2-109

2. Remove the remaining coolant hoses; then remove

the clamps and hoses connecting the oil reservoir to

the engine.



NOTE: For assembling purposes, note the location

of the oil and coolant hoses.

3. Remove the six flange nuts securing the exhaust

manifold to the cylinder head; then remove the mani-

fold and discard the gaskets.

ZJ048A

4. Remove the banjo bolts securing the oil feed pipe to

the turbocharger and engine. Discard the crush wash-

ers.

744-771B



NOTE: For assembling purposes, note the size of

the oil port and thread taper of the banjo bolts.

IO028



NOTE: Steps 5 and 6 are for the turbo models only.

5. Remove the three lock nuts and washers (A) securing

the bracket of the turbocharger to the engine; then

loosen the lock nuts (B) securing the bracket to the

turbocharger.

743-780C

6. Remove the lock nuts and washers securing the

exhaust manifold to the cylinder head; then carefully

remove the turbocharger and exhaust manifold

assembly. Remove the cap screws securing the lower

heat shield to the exhaust manifold and turbocharger.

744-003A



NOTE: If removing the bracket from the turbo-

charger outlet, note the location of the backing plate
for assembling purposes.

TZ063A

7. Remove the two cap screws (A) securing the water

inlet hose fitting and remove the fitting; then remove

the cap screws (B) securing the starter motor to the

engine. Remove the starter motor.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды