manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 268 / 535

Поделиться
Скачать
Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 268

5

5-7

REPLACING TPS

NOTE: Replacing the TPS is for out of warranty

snowmobiles only.

NOTE: It is important that the throttle shaft is in the

completely closed position for this procedure.

Removing

1. Disconnect the throttle cable from the throttle shaft.

2. Rotate the idle screw counterclockwise until it no

longer contacts the throttle shaft stop. The throttle

shaft should now be completely closed.

3. Disconnect the TPS wiring harness from the TPS;

then noting the position of the TPS, remove the two

screws securing the TPS to the throttle body housing

and remove the sensor. Account for the O-ring which

fits into groove of throttle body.

Installing

1. Apply a light film of silicone grease to the O-ring.

Install the O-ring into the groove.

MS399

2. Install the new TPS onto the throttle shaft by align-

ing the “flats” on the throttle shaft cam with the

“flats” on the sensor; then rotate the sensor until

properly positioned on the throttle body.

MS400A

3. Install the two screws, flat washers, and lock washers

securing the sensor to the throttle body. Do not

tighten at this time.

4. Adjust the TPS - see Adjusting TPS in this sub-sec-

tion.

5. Disconnect the adjustment tool harness from the

TPS. Connect the snowmobile TPS harness to the

newly installed or adjusted TPS.

NOTE: Before installing the TPS harness connector,

apply dielectric grease to the connector pins.

Throttle Position Sensor 

(4-Stroke)

NOTE: On the non-turbo models, remove the air

silencer. Proceed to Air Silencer (1100 cc Non-Turbo)
sub-section in Section 3 and follow steps 1-12 of
REMOVING.

NOTE: On the turbo models, remove the console

and left-rear spar panel.

VERIFYING TPS ADJUSTMENT TOOL

Before using the TPS adjustment tool, verify its battery

condition. The battery used in the tool is a 9-volt battery.

To check battery condition, use a digital volt/ohmmeter

set on DC volt scale. Test between the adjustment tool

black and red jacks. Insert the red lead of the digital volt-

meter into the red jack of the adjustment tool and the

black lead of the digital voltmeter into the black jack of

the adjustment tool. The green power light of the ana-

lyzer should now be illuminated. If voltage is found

below 4.9 volts, replace the battery.

NOTE: The appropriate Test Harness must be

plugged into the analyzer for testing voltage. Always
verify battery voltage is at least 4.9 DC volts for accu-
racy.

CHECKING TPS

NOTE: If the snowmobile is in warranty, breaking

the seal on the idle screw jam nut or the Phillips-head
screws on the TPS will void warranty. If the TPS is
tested out of specification, the throttle body must be
replaced. If the snowmobile is out of warranty, pro-
ceed to Adjusting TPS. 

Model

TPS TOOL

(DC VOLTS)

ANALYZER TOOL 

(DC VOLTS)

500 cc

Full-Closed

0.412-0.414

Idle 0.710-0.818

0.710-0.818

Full-Open

3.472-4.048

3.470-4.046

600 cc

Full-Closed

0.412-0.414

Idle 0.646-0.754

0.646-0.754

Full-Open

3.472-4.485

3.470-4.485

DIAGNOSTIC TOOL

800 cc

Full-Closed

0.412-0.414

Idle 0.646-0.754

3.99° 

-6.66°

Full-Open

3.472-4.485

74.97°-89.37°

1000 cc

Full-Closed

0.392-0.394

Idle 0.591-0.699

4.75°-7.55°

Full-Open

3.477-4.054

77.39°-91.66°

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов