Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 495 / 535

background image

8-5

8

14. Secure the wiring and brake hose to the steering sup-

port with the routing clips.

15. Using a suitable handlebar support stand, tip the

snowmobile on its PTO-side.

16. From beneath the front end, secure the steering post

to the steering post stop with the washer and lock nut

(threads coated with green Loctite #609). Tighten the

lock nut to 30 ft-lb.

FC199

Steering Post (Bearcat/

F-Series/T-Series/Z1)

REMOVING

1. Open the hood; then remove the two torx-head

screws securing the console to the headlight support

bracket.

0743-777

2. Lift the rearward end of the console and disconnect

the main/hood harness connector; then remove the

console.

3. On the standard models, remove the four cap screws,

lock nuts, and adjuster block caps securing the han-

dlebar/riser assembly to the steering post; then lay

the handlebar/riser assembly aside. Account for the

lower adjuster block.

4. On the LXR/Sno Pro/EXT models, remove the two

screws from the handlebar pad; then remove the self-

tapping screw securing the retainers (A) to the riser

block assembly. Remove the retainer.

0744-927

5. On the LXR/Sno Pro/EXT models, unlock the cam

lever and unthread the lever from the lock rod (B);

then remove the lock rod and account for the two

bottom cap springs (C).

6. Remove the four cap screws securing the upper bear-

ing bracket to the upper support plate.

FS182A

7. On the Bearcat 570/F-Series/T-Series, remove the

springs securing the expansion chamber; then

remove the expansion chamber from the engine com-

partment. Account for the rubber exhaust bumper.

! WARNING

Care must be taken to securely lock the handlebar
cam lever to prevent unexpected “movement” of the
handlebar during operation over rough terrain. DO
NOT offset the handlebar so steering (maximum right/
left turning capabilities) are altered or throttle and
brake controls will be affected.

CAUTION

Do not rotate the handlebar to a position allowing air
to enter the brake system.

Manual

Table of Contents

«
...
493
494
495
496
497
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренд: Ski-Doo Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды