Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 534 / 535

background image

8-44

6. Check headlight aim (see Adjusting Headlight Aim

in this sub-section).

Adjusting Headlight Aim

The headlight can be adjusted for vertical aim of the

HIGH/LOW beam. The geometric center of HIGH beam

zone is to be used for vertical aiming.

1. Position the snowmobile on a level floor so the head-

light is approximately 8 m (25 ft) from an aiming

surface (wall or similar surface).



NOTE: There should be an “average” operating load

on the snowmobile when adjusting headlight aim.

2. Measure the distance from the floor to midpoint of

the headlight.

3. Using the measurement obtained in step 2, make a

horizontal mark on the aiming surface.

4. Make a vertical mark intersecting the horizontal

mark on the aiming surface directly in front of the

headlight.

5. Start the engine. Select the headlight dimmer switch

HIGH beam position. DO NOT USE LOW BEAM.

6. Observe the headlight beam aim. Proper aim is when

the most intense beam is centered on the vertical

mark 5 cm (2 in.) below the horizontal mark on the

aiming surface.

0741-448

7. Adjust the headlight housing mounting screws (on

the 3-bulb models) or the console adjustment knobs

(on the 4-bulb models) until correct aim is obtained.

Shut the engine off.

! WARNING

Do not operate the snowmobile unless headlight beam
is adjusted properly. An incorrectly adjusted beam will
not provide the operator the optimum amount of light.

Manual

Table of Contents

«
...
532
533
534
535
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренд: Yamaha Страницы: 279

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды