Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 530

Страница: 530 / 535

8-40

2. Secure the windshield to the console with the torx-

head screws.

3. Using a new plastic rivet, secure the windshield to

the windshield bracket.

Windshield (TZ1 Turbo)

REMOVING

1. Remove the mounting hardware securing the mirrors

to the windshield.

2. Remove the torx-head screws securing the wind-

shield to the console and windshield support; then

remove the plastic rivets securing the windshield to

the front bracket. Remove the windshield.

0744-554

INSTALLING

1. Place the windshield into position on the console and

bracket.

2. Secure the windshield using the torx-head screws,

washers, and rivets according to the illustration.

Windshield (Z1 Turbo)

REMOVING

1. Remove the torx-head screws and plastic rivets

securing the windshield to the console.

2. Remove the windshield.

0743-434

INSTALLING

1. Place the windshield into position on the console.

2. Secure the windshield using the torx-head screws

and rivets according to the illustration.

Backrest/Rack Assembly

(Bearcat)

REMOVING

1. Remove the cap screws, washers, and cap nuts secur-

ing the rack to the backrest.

2. In turn on each side, remove the two cap screws

(inside the tunnel) securing the backrest assembly to

the tunnel. Account for the washers.

3. If applicable, disconnect the passenger handwarmer

wiring harness.

4. Remove the backrest assembly from the tunnel.

Account for the two spacers.

INSTALLING

1. Place the backrest assembly and spacers (located on

the rear hole on each side) into position and align

holes with tunnel mounting holes.

2. Install the cap screws with washers from the inside

of the tunnel and secure with the washers and lock

nuts. Tighten securely.

3. In turn on each side, install the 1/4-in. cap screw in

the front hole and the 5/16-in. cap screw in the rear

hole. Secure with a flat washer and lock nut. Tighten

securely.

4. If applicable, connect the passenger handwarmer

wiring harness.

5. Place the rack into position and secure with the cap

screws, washers, and cap.

Tunnel/Chassis/Rear

Bumper/Snowflap

(Bearcat XT)

REMOVING/REPLACING TUNNEL

To remove and/or replace a tunnel on a particular snow-

mobile, a number of removing and installing component

sequences must be followed. The technician must in turn

go to the following sections in this manual and refer to

the appropriate removing/installing sub-sections. When

doing these sequences, the technician should use discre-

tion and sound judgment.

A. Section 2 - Engine

B. Section 6 - Drive Train/Track/Brake Systems

C. Section 7 - Rear Suspension

D. Section 8 - Steering and Body

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 530 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: